BEP Pro Installer 400A Dual Bank Control Switch - MC10 Electrical

Pro Installer 400A Dual Bank Control Switch - MC10

Another addition to our multi-award winning Pro Installer EZ Mount line, the innovative Dual Bank Control Switch is like 3 switches in one, House, Start and parallel emergency. Providing intuitive, easy control for the boater, the dual-bank control switch features a unique isolated position that allows use of household loads and the VHF radio if the engine needs to be electrically isolated, or allows for isolation of the engine during maintenance while providing electricity to power loads (for lights, stereo, refrigerator, etc.). For boats or vehicles equipped with a single engine and house battery bank, Dual Bank Control allows the use of battery banks optimized for their respective loads; a properly sized deep cycle battery for household and battery chargesthin plate starter for the motor. Additionally, sensitive electronics are isolated from starter-induced voltage spikes because the house and motor loads are separated during normal operation, unlike Selector battery disconnect switches. As simple as 1, 2, 3, these revolutionary EZ Mount battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnect height, EZ-Mount Battery Switches "gang" directly with the Pro Installer busbar line, resulting in the fastest, most compact installations. Optimized cable access makes installation easier.

Tested to UL1107, CE ignition protection
10mm tinned copper studs (3 /8 inch)
Stainless steel washers and nuts
Fiber reinforced plastics
400 A continuous/ 600A 5 minutes intermittent / 1500A 10 seconds Start (cable size to achieve 120mm} ratings, 4/0, smaller cable size will reduce current rating)
Waterproof IP67
Same interconnect height as Pro Installer
Removable button allows isolation during maintenance
3 removable side plates for protection
Industry standard 3.85 x 3.85 inch footprint
For surface mount only
Each Pro Installer battery switch is fully tested for pressure tightness, rotational force and electrical load

Specifications
Mounting: Surface, rear or front
Voltage: 48 V DC (for 12-48 V systems, both banks must have the same voltage)
Rating: 400 Cont / 600 Inter / 1500 Crank
Dims: 3.85" x 3.85" x 3.62"
Operation: 1, 1/2, parallel, off
Stud: 4x 10mm (3.8")

WARNING: This product can expose you to chemicals including di(2-ethylhexyl) phthalate (dehp), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information,

A new generation of powerful battery switch with excellent performance and functions, suitable for installers and end users. Three mounting options: surface, rear panel and front panel...
PRODUCT ID: 58595
SKU: NVN-58595
CSKU: CWR-58595
REWRITE: 69706-bep-pro- installer-400a-dual-bank-control
MPN: 772-DBC
UPC: 843687007807
ASIN: B00NW4V4MY
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU: 69-772DBC
NAME: BEP Pro Installer 400A control switchDual Bank Switch - MC10
EX_NAME: BEP PRO INSTALLER 400A DOUBLE BANK CONTROL SWITCH
PTITRE: BEP Pro Installer 400A Dual Bank Control Switch - MC10
TYPE: Electric | Battery Management
SUPPLIER: BEP Marine
VEHICLES & PARTS> VEHICLE PARTS & ACCESSORIES> WATERCRAFT PARTS & ACCESSORIES BEP Pro Installer 400A Dual Bank Control Switch - MC10 - 772-DBC

Gtags:

Switch

GSpecs:

BEP Pro Installer 400A Dual Bank Control Switch - MC10 Product Description Pro Installer 400A Dual Bank Control Switch - MC10

Another addition to our multi-award winning Pro Installer EZ Mount line, The innovative Dual Bank Control Switch is like 3 switches in one, home, start and parallel emergency. Providing intuitive, easy control for the boater, the dual-bank control switch features a unique isolated position that allows use of household loads and the VHF radio if the engine needs to be electrically isolated, or allows for isolation of the engine during maintenance while providing electricity to power loads (for lights, stereo, refrigerator, etc.). For boats or vehicles equipped with a single engine and house battery bank, Dual Bank Control allows the use of battery banks optimized for their respective loads; a deep cycle batterye suitable size for domestic loads and thin plate starting batteries for the engine. Additionally, sensitive electronics are isolated from starter-induced voltage spikes because the house and engine loads are separated during normal operation, unlike selector switch switches. As simple as 1, 2, 3, these revolutionary EZ Mount battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnect height, EZ-Mount Battery Switches "gang" directly with the Pro Installer busbar line, resulting in the fastest, most compact installations. Optimized cable access makes installation easier.

Tested to UL1107, CE ignition protection
10mm tinned copper studs (3 /8 inch)
Stainless Steel Washers and Nuts
Fiber reinforced plastics
400A continuous / 600A 5 minutes intermittent / 1500A 10 seconds Startup (cable size to achieve values rated 120mm}, 4/0, smaller cable size will reduce current rating)
Waterproof IP67
Same interconnect height as Pro Install
Removable button allows insulation during maintenance
3 oval side plates for protection
Dimensions industry standard 3.85 x 3.85 inch
For surface mount only
Each Pro Installer Battery Switch is fully tested for pressure tightness, rotational force and electrical load tested

Specifications
Mounting: surface, rear or front
Voltage: 48V DC (for 12-48V systems, both banks must have the same voltage) 1/2, parallel, off
Stud: 4 x 10 mm (3.8")

This product can expose you to chemicals including di(2-ethylhexyl) phthalate (dehp) which is recognized by the 'State of California as causing cancer, birth defects or other reproductive harm. For more information, go to P65Warnings.ca.gov.

A new generation of. Powerful battery switch with excellent performance and functions, suitable for installers and end users. Three mounting options: surface, rear panel and front panel...

Frequently Asked Questions (FAQ) about BEP Pro Installer 400A Dual Bank Control Switch - MC10 Who is BEP Marine?
How to describe BEP Pro Installer 400A Dual Bank Control Switch - MC10?
What positions exist in this product?
Lockable product?
Does this switch have a disconnect optionu field of the alternator?
Who is the BEP Marine? BEP designs and manufactures a range of high quality electrical solutions designed for harsh marine and motorhome environments. Each product manufactured meets rigorous performance specifications and is designed to withstand conditions at sea and on land. BEP engineers and product managers continue to develop the next generation of energy management products. How to describe the BEP Pro Installer 400A Dual Bank Control Switch – MC10? A new generation of powerful battery switch with excellent performance and functions, suitable for installers and end users. Three mounting options: surface, rear panel and front panel...What positions exist in this product? 1-1/2-Parallel-OffLockable product? No, does this switch have an option to disconnect the alternator field? No

Economysez $34 when you purchase the BEP Pro Installer 400A Dual Bank Control Switch - MC10 for only $54 from NVN Marine ! Same day dispatch before 3 p.m. BEP Pro Installer 400A Dual Bank Control Switch - Technical Specifications MC10

Type:	Electric \| Battery management
Supplier:	BEP Marine
Weight:	1.2 lbs
AFD:	No
Lockable:	No
Positions:	1-1/2-Parallel-Off
Continuous intensity:	400a
User Guide:	Download PDF
Product manual:	Download PDF
Product brochure:	Download the PDF
Product installationt:	Download PDF

BEP Pro Installer 400A Dual Bank Control Switch - MC10BEP Pro Installer User Reviews 400A Dual Bank Control Switch - MC10 Shipping & Returns

Shipping Weight:	1, 2 lb
Box sizes:	4.00 (h) x 7.00 (w) x 8, 00 (l)
Cubic feet:	224.0
Returnable:	Yes
P65:	Yes

For detailed shipping terms, please see our shipping policy and you can find our return and refund policy here.