NavPod PP5050 Uncut PowerPod (Usable Face = 12.75" x 8.55" H) (12.75" W x 8.5" H) - Carbon Black Boat Outfitting

Uncut PowerPod PP5050 (usable face = 12.75" x 8.55" H) (32.4 cm wide x 21.7 cm high) - Carbon Black

PowerPods are designed for serious offshore boaters. He demands the most from his boat and its electronics. It needs strong, sturdy support to protect vital electronic components from the harshest offshore navigation conditions. Rugged and secure, yet clean and attractive, PowerPods are better than rack mounting. Over 70 pre-cut PowerPods are available for all products from popular manufacturers. The 1.8" opening in the swivel tube provides plenty of room to pass through wires and connectors. PowerPods are positioned at a 20-degree tilt-back viewing angle.

PowerPods for Sail are intended to be mounted on a flat surface Perhaps under the cubby or aft end of the cockpit table, e.especially on twin wheel boats.

Structural rigidity

Gen3 improvements now include acrylic coated ABS material of thicker gauge which improves strength and prOffers better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially harmful effects on plastic. These NavPods are really strong!

Waterproof seal

All NavPods are made with a double seal system providing an excellent seal between the front and back of the NavPod. This seal offers the best protection for your marine electronics. NavPods are designed to withstand off-navigation conditionsmost difficult and wet shores. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The Poran Microcell Polyurathane internal seal is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel

The NavPod uses all 316 stainless steel hardware provided with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. For NavPods Gen3, we provide tamper-proof nickel-chrome-plated stainless steel screws for added security combined with a little bling!

Commitment toquality

We are committed to producing high quality waterproof enclosures for marine electronics. We stand behind our commitment by offering a 10-year warranty on all new NavPod Gen3s. We want you to be a NavPod customer for life and are ready to earn your trust and loyalty.

Compared to rack installation, PowerPods for Power is a better choice. PowerPods have the advantage of having a rotating base, which can provide a sleek appearance for built-in installation.
PRODUCT ID: 63963
SKU: NVN-63963
CSKU: CWR-63963
REWRITE: 75074-navpod-pp5050-powerpod-uncut-usable-face
MPN: PP5050-C
br> UPC: 659988112559
ASIN: B082BFNTTM
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: NavPod PP5050 PowerPod no cut (Usable face = 12.75" x 8.55" H) (32.4 cm wide x 21.7 cm high) - Carbon Black
NAME_EX: NAVPOD POWERPOD NON-NECKPE (USABLE FACE = 12.75" 4cm wide x 21.7cm high) - Carbon Black
TYPE: Boat Equipment Display Mounts
SELLER: NavPod
ELECTRONICS> MARINE ELECTRONICS
Amazon Category :

NavPod PP5050 Uncut PowerPod (Usable Face = 12.75" x 8.55" H) (12.75" W x 8.5" H) - Black of carbon

Gtags:

GSpecs:

NavPod PP5050 Uncut PowerPod (Usable Face = 12.75" x 8.55" H) (12.7" W x 8.5" H) - Carbon Black Product Description

PP5050 PowerPod Uncut (usable face = 12.75" x 8.55" height) (32.4 cm wide x 21.7 cm high) - Carbon Black

PowerPods are designed for serious boaters who blast offshore. He demands the most from his boat and its electronics. It needs strong, sturdy support to protect vital electronic components from the harshest offshore navigation conditions. Rugged and secure, yet clean and attractive, PowerPods are better than rack mounting. Over 70 pre-cut PowerPods are available for all products from popular manufacturers. The 1.8" opening in the swivel tube provides plenty of room to pass through wires and connectors. PowerPods are positioned at a 20-degree tilt-back viewing angles.

PowerPods for Sail are intended to be mounted on a flat surface. Perhaps under the cubbyhole or aft end of the cockpit table especially on twin wheel boats.

Structural RiGidity

Gen3 improvements now include thicker gauge acrylic coated ABS material which improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially harmful effects on plastic. These NavPods are really strong!

Waterproof seal

All NavPods are made with a double seal system providing an excellent seal between the front and rear ofuNavPod. This seal offers the best protection for your marine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The Poran Microcell polyurethane internal seal is not 50% thicker and is not subject to "retentive compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel

The NavPod uses all 316 stainless steel hardware provided with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. For Gen3 NavPods, we provide tamper-proof nickel-chrome plated stainless steel screws for added security combined with a little bling!

Commitment to quality

Compared to rack installation, PowerPods for Power is a better choice. PowerPods have the advantage of having a rotating base, which can provide a sleek appearance for a built-in installation.

Frequently asked questions (FAQ) about NavPod PP5050 Uncut PowerPod (usable face = 12.75" x 8.55" H) (32. 4 cm wide x 21.7 cm high) - Carbon Black Who is the NavPod?
How to describe the NavPod PP5050 PowerPod not coupé (usable face = 12.75" x 8.55" H) (32.4 cm wide x 21.7 cm high) - Carbon Black?
Is it cut or uncut?
How to mount or what is the mounting style of the Uncut NavPod PP5050 PowerPod (Usable Face = 12.75" x 8.55" H) (12.75" W x 8.5" H) - Black carbon?
What is the size of the usable surface of the product?
Who is the NavPod? Navpod is a better way to mount your fishfinder, radar or GPS. The unique waterproof seal, build quality and attractive design make the best-built instrument case ever available to the marine industry.try. Features of all Navpods include waterproof silicone seal, tamper-proof clips for added security and convenience, concealed wiring and clean installation for easy access. How to Describe NavPod PP5050 Uncut PowerPod (Usable Face = 12.75" x 8.55" H) (32.4cm W x 21.7cm H) - Carbon Black? Compared to rack installation, PowerPods for Power are a better choice. PowerPods have the advantage of having a rotating base, which can provide a clean appearance for built-in installation. Is it cut or uncut? Uncut How to mount or what is the mounting style of the Uncut NavPod PP5050 PowerPod (Usable Face = 12.75" x 8.55" H) (32.4cm W x 21.7cm) cm high) - Carbon black? DashWhat is the size of the usable surface area of the product? 12.75"L x 8.75"H

Save $108 when you purchase the NavPod PP5050 Uncut PowerPod (Usable Face = 12.75" x 8.55"H) (32.4cm W x 21.7cm H) - Carbon Blackfor only $381 at NVN Marine! Same day dispatch before 3 p.m.NavPod PP5050 Uncut PowerPod (usable face = 12.75" x 8.55" H) (32.4 cm wide x 21.7 cm high) - Technical specifications carbon black

Type:	Outfittingof boat \| Display Media
Supplier:	NavPod
Cut/Uncut:	Uncut
Edit Style:	Pulled
Usable side:	12.75"W x 8.75"H

NavPod PP5050 Uncut PowerPod (usable face = 12.75" x 8.55" H) (32.4 cm wide x 21.7 cm high) - Carbon Black User ReviewsNavPod PP5050 Uncut PowerPod (usable face = 12.75" x 8.55" height) (32.4 cm wide x 21.7 cm high) - Carbon Black Shipping & Returns

For detailed shipping policy, please see our shipping policy and you can find our return and refund policy here.