Newmar BI-100 12v battery integrator Electrical
Using multiple battery banks requires that batteries be connected or "integrated" only when a charging voltage is present so that they can be charged simultaneously and then disconnected or "isolated" when used for allow selective discharge and avoid having the secondary or backup battery drain into the primary battery.
The new Battery Integrator performs this function automatically, acting as a "smart" switch to connect independent battery banks only when a charging voltage is present. Otherwise, they are isolated and discharge between the banks is prevented.
The traditional robust and reliable diode isolator can also be used for this function, as it also maintains the isolation between the banks and allows the load from multiple sources. However, a disadvantage is inefficiency when voltage is lost whencurrent passes through the diodes, resulting in undercharging if the charging source does not compensate for the voltage drop.
The Battery Integrator remedies this through the use of an extremely low resistance contactor which causes no voltage drop in the charging system, while multiple batteries are charged as a single bank each time that a charging source of approximately 13.2 VDC or 26.4 VDC or greater is present (depending on model).
When the alternator or charger is turned off or a heavy load is drop the voltage below the disconnection point, the unit breaks the common link between the banks. This allows selective battery discharge and prevents 'spill' from a more charged battery into a less charged battery.
The unit can also be activated via the key starter or a manual switch to provide an additional "boost". of the secondary battery each timethat the starter is engaged and the unit detects that there is sufficient voltage in this battery to provide assistance.
For systems with more than two banks, an additional unit can be installed for each additional bank so provide the same isolation and integration as described above.
The battery integrator is ideal for multiplying the single load output of an inverter-charger to maintain both the internal battery and an engine starting battery, then to isolate them during operation of the inverter, so that current is drawn from the internal battery only.
Features
- Allows two separate banks to be charged without voltage drop, while maintaining 100% isolation at all other times. For systems with three or more banks, an additional unit can be installed for each additional bank
- Rob contactorHeavy duty silver plated, continuous duty rated at 100 amps
- Voltage sensing circuit, epoxy Heavy-duty encapsulated continuous solenoids are all designed for use in marine environments
- Easy to install : compact size - can be mounted in any orientation
- Easy three-wire connection for two bench systems (BATT+, BATT+, GROUND)
- Terminal block for optional wiring Remote lighting indicating when battery banks are integrated
- Optional internal connection can be wired via key starter or manual switch, linking the batteries together for an extra boost while starting the motor
Using multiple battery packs requires connecting or "integrating" the batteries only when a charging voltage is present, so they can be charged at the same time, then disconnected or charged.
PRODUCT ID: 1001156
SKU: NVN-1001156
CSKU: CWR-1001156
REWRITE: 1012267-newmar-bi-100-12v-battery-integrator
MPN: BI-100
br> br> UPC:
ASIN:
WSKU: NEWBI100
SSKU:
NAME: Newmar BI-100 12 V Battery Integrator
PTITLE: Newmar BI-100 12 V Battery Integrator
TYPE: Electrical -> Battery Isolators
SELLER: NewMar Gtags:
G Specs:
Newmar BI-100 12V Battery Integrator Product Description
Using multiple battery banks requires that batteries be connected or "integrated" only when a charging voltage is present so that they can be charged simultaneously , then disconnected or "isolated" when in operation. use to allow selective discharge and prevent the secondary or backup battery from draining into the primary battery.
The new Battery Integrator performs this function automatically, acting as a "smart" switch to connect independent battery banks only when a charging voltage is present. Otherwise, they are isolated and discharge between the banks is prevented.
The traditional robust and reliable diode isolator can also be used for this function, as it also maintains the isolation between the banks and allows the charging from multiple sources. However, a disadvantage is inefficiency when voltage is lost as current passes through the diodes, resulting in undercharging if the charging source does not compensate for the voltage drop.
The battery integrator addresses this problem by using an extremely low resistance contactor that causes no voltage drop in the charging system, while the multiple batteries are charged as a single bank each time A charging source of approximately 13.2 VDC or 26.4 VDC or more is present (depending on model).
When the alternator or charger is turned off or a heavy load drops the voltage below the disconnection point, the unit breaks the common link between the banks. This allows selective discharge of the battery and prevents 'spill' from a more charged battery into a less charged battery.
The unit can also be activated via the key starter or a switchmanual switch to provide additional boost. from the secondary battery whenever the starter is engaged and the unit senses that there is sufficient voltage in that battery to provide assistance.
For systems with more than two banks, a unit Additional can be installed for each additional bank to provide the same isolation and integration as described above.
The battery integrator is ideal for multiplying the single load output of an inverter-charger to maintain at both the house bank and a motor start bank, then to isolate them while the inverter is running, in order to maintain the current. is taken only from the company bank.
Features
- Allows two separate banks to be charged without voltage drop, while maintaining 100% isolation at all other times. For systems of three or more banks, one additional unitaire can be installed for each additional bank
- Heavy duty silver plated contactor, continuous duty rated at 100 amps
- Voltage sensing circuit, epoxy The encapsulated, heavy duty continuous solenoids are all designed to use in marine environments
- Easy to install: compact size - can be mounted in any orientation
- Easy three-wire connection for two bank systems (BATT+, BATT+, GROUND)
- Terminal for optional wiring of remote light indicating battery banKs are built in
- Optional internal connection can be wired via jump starter key or manual switch, connecting the batteries together for extra boost during engine starting
Using multiple battery packs requires connecting or "integrating" the batteries only when a charging voltage is presentte, so that they can be charged at the same time and then disconnected or charged.
Frequently asked questions (FAQ) about the Newmar BI-100 12 V battery integrator Who is the NewMar?
How to describe the Newmar BI-100 12 V battery integrator?
br/> What are the strong points of the Newmar BI-100 12v battery integrator?
Who is NewMar? Newmar DC Power has been a leading manufacturer of high quality communications DC power products for over 50 years. Newmar powers critical equipment in industries such as marine, telecommunications, networking, land mobile and IOT automation. Newmar is dedicated to high quality with fast delivery and by mainta Having a large inventory of all products and components, they can quickly ship standard products and design, assemble and ship complete power plants in a fractiontime required by most other system integrators. Providing the industry's fastest delivery of high-quality grocery products is what sets Newmar apart. Newmar offers an extensive range of DC power products with a well-deserved reputation for high reliability and quality in powering broadband wireless, iDAS, oDAS, microwave, cellular and land mobile applications. Available in 2V, 24V and 48V DC, they offer solutions including DC power systems, hot-swappable rectifiers, power supplies, DC-DC converters, DC-AC inverters, distribution panels DC, DC power conditioners, DIN rail DC inverters, DIN. Railway power supplies and installation accessories. How to describe the Newmar BI-100 12V Battery Integrator? Using multiple battery packs requires connecting or "integrating"batteries only when a charging voltage is present, so that they can be charged at the same time and then disconnected or charged. What are the strong points of the Newmar BI-100 12 V battery integrator?
Save $118 when you purchase the Newmar BI-100 12V Battery Integrator for only $118 b> from NVN Marine! Same day dispatch before 3 p.m. Newmar BI-100 12V Battery Integrator Technical Specifications
| Type: | Electric | Battery Isolators |
|---|---|
| Supplier: | NewMar |
| Weight: | 2.0 lbs |
| Shipping Weight: | 2.0 lbs |
|---|---|
| Box sizes: | 1.00 (h) x 1.00 (w) x 1.00 (l) |
| Cubic feet: | 1.0 |
| Returnable: | Yes |
| USPS First Class: | Yes |
| P65: | Yes |
For detailed shipping terms, please see our shipping policy and you can find our return and refund policy here.
