Pre-cut NavPod RailMount for Garmin GPSMAP 8410xsv and 8610xsv (fits 1″ or 1.25″ tubes) Boat Outfitting

Pre-cut RailMount for Garmin GPSMAP 8410xsv and 8610xsv (fits 1" or 1.25" tubes)

RailMount NavPods are best used for mounting a control of an autopilot or a navigation instrument, or a small chart plotter on an existing protective base. Fits any 1" or 1.25" diameter tube. A stainless steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle on a rainy day. All wiring runs from the NavPod down the center of the stainless steel arm and into the base shield. This application provides a clean, sturdy installation for electronics without replacing the base guard.

Rail mounts are designed for all popular standard size instruments as well as chart plotters. 7 and 9 inches.

Structural rigidity– Gen3 improvements now include thicker gauge acrylic-coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for a greater amount of watertight seal. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.

Waterproof Seal – All RailMount NavPods are manufactured with a double seal system providing an excellent seal. This seal offers the best protection for your marine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The jPoron Microcell internal polyurethane anoint is now 50% thicker and is not subject to "defined compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The gasket will continue to do its job.

Chrome Nickel Plated Stainless Steel – We use all 316 steel hardware supplied with each NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. Tamper-proof nickel-chrome-plated stainless steel screws provide security combined with a little style!

Commitment to quality – We stand behind our commitment by offering a 10-year warranty on all new NavPods Gen3.

Pre-cut RailMount for Garmin GPSMAP 8410xsv and 8610xsv (fits 1" or 1.25" tubes) ")

RailMount NavPods are best used for mounting an autopilot control, navigation instrument, or small chart plotter to an existing protective cradle . Fits any 1" or 1.25" diameter tube. A stainless steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle on a rainy day. All wiring runs from the NavPod down the center of the stainless steel arm and into the base shield. This application provides a clean, sturdy installation for electronics, without replacing the base guard.

Rail mounts are designed for all inpopular standard size instruments as well as for 7 and 9 inch chartplotters.

Structural Rigidity – Gen3 enhancements now include a thicker gauge acrylic cap and ABS material that improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.

Waterproof Seal – All RailMount NavPods are manufactured with a double seal system providing an excellent seal. This seal offers the best protection for your marine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. The ameliorations Gen3 include a thicker silicone outer seal with an improved flush fit. The internal Poron Microcell polyurethane gasket is now 50% thicker and is not subject to "set compression" like many rubber compounds. This is important when you need to open the NavPod in the future in order to use your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel – We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. Nickel-Chrome Plated Stainless Steel Tamper Proof Screws provide security combined with a little style!

Commitment to Quality – We stand by our commitment by offering a 10-year warranty on all newcalves NavPods Gen3.

RailMount NavPods are most suitable for installing autopilots, navigation instruments or small chartplotters on existing base guards. Can be installed on any pipe with a diameter of 1 or 1.25. Chrome-plated stainless steel arms are used to install the NavPod. The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle on a rainy day. All wiring runs from the NavPod to the center of the stainless steel arm and then into the base shield. This application can provide a clean and robust installation of electronic devices without the need to replace the base cover.

Frequently Asked Questions (FAQ) about Pre-Cut NavPod RailMount for Garmin GPSMAP 8410xsv and 8610xsv (fits 1″ or 1.25″ tubes) Who is the NavPod?
How to describe the NavPod RailMount Pre-Cut for Garmin GPSMAP8410xsv and 8610xsv (fits 1″ or 1.25″ tubes)?
Who is the NavPod? Navpod is a better way to mount your fishfinder, radar or GPS. The unique watertight seal, build quality and attractive design make the best-built instrument housing ever available to the marine industry. Features of all Navpods include waterproof silicone seal, tamper-proof clips for added security and convenience, concealed wiring and clean installation for easy access. How to describe the NavPod RailMount Pre-Cut f/Garmin GPSMAP 8410xsv & 8610xsv (fits 1″ or 1.25″ Tube)? RailMount NavPod are most suitable for installing autopilots, navigation instruments or small chartplotters on existing base guards. Can be installed on any pipe with a diameter of 1 or 1.25. Chrome-plated stainless steel arms are used to install the NavPod. The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle on a rainy day. All wiring extends from the NavPod down the center of the stainless steel arm and then into the base shield. This application can provide a clean and robust installation of electronic devices without the need to replace the base cover.

Save $141 when you purchase the NavPod RailMount Pre-Cut f/Garmin GPSMAP 8410xsv & 8610xsv (fits 1″ or 1.25″ tubes) for only $458 from NVN Marine! Same day dispatch before 3 p.m. NavPod RailMount Pre-Cut f/Garmin GPSMAP 8410xsv & 8610xsv (fits 1″ or 1.25″ tubes) Technical specificationsns

Type:	Boat equipment \| Display Media
Supplier:	NavPod
Weight:	7.7 lbs

NaPre-Cut vPod RailMount for Garmin GPSMAP 8410xsv & 8610xsv (Fits 1″ or 1.25″ Tubes) User ReviewsNavPod RailMount Pre-Cut f/Garmin GPSMAP 8410xsv & 8610xsv (Fits 1″ or 1.25″ Tubes) Shipping and return

Shipping weight:	7.7 lbs
Box sizes:	9.00 (h) x 13.00 (w) x 14.00 (w)
Cubic feet:	1638.0
Returnable:	Yes

For detailed shipping terms, please see our Shipping Policy and you can find our Returns and Refunds Policy here.