PSS Shaft Seal 1-¾" Shaft 3" Tube Marine Hardware
PSS Shaft Seal, 1-3/4" Shaft, 3" TubeShaft Diameter: 1-3/4 "
Stern tube Diameter (D): 3"
Total length (A): 9.175"
Total length (compressed) ) (Compressed A): 8.175 "
Rotor diameter (B): 3.75"
Carbon cuff diameter (C): 3.25"
Rear Cuff Length (E): 2"
PSS Shaft Seal is the marine mechanical seal best-selling worldwide and is installed as standard equipment by many of the most reputable boat builders/yards The PSS shaft seal is also recognized as the leading retrofit seal (market). secondary) in the global market Certified by
Bureau Veritas, ABS and Rina: boat builders/yards recognize the value of installing PSS as it eliminates maintenance, constant adjustment and. Or cost associated with traditional cable glands.Along with these benefits, the PSS shaft seal helps eliminate water in the bilge. (100% waterproof) and wear down to the rope shaft. The PSS shaft seal
can be easily retrofitted and is available for shafts ranging from 3/4"
(20 mm) to 6" (150 mm).
The PSSshaft seal is a mechanical seal created between the flat surfaces of the rotating stainless steel rotor and the fixed carbon flange. The carbon fixed bridle is attached to the ship's stern tube with hose clamps and the carbon bridle is attached to the front of the bellows with hose clamps. The stainless steel rotor is mounted on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is attached to the shaft with set screws. This compression (preload) maintains contact between the faces and allows the
PSS to compensate for the thrust of the propeller. The carbon flange is reamed larger than the diameter of the shaft, which allows it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two O-rings that are recessed into the collar bore. These O-rings rotate with the stainless steel shaft and rotor and experience no wear during operation.
**As with any rubber hose below the waterline, the PSS bellows must be inspected on a regular basis for any signs of wear, aging or chemical deterioration.
PYI suggests, as preventative maintenance, that the PSS bellows be replaced every six years. When replacing the bellows, it is recommended to also replace the stainless steel rotor O-rings and adjustment screws. Sulfuric acid vapors will accelerate the deterioration of rubber, as will an ozonator.
Maintenance kit includesend the items you need to properly maintain your PSS shaft seal. Kit includes one (1) PSS. below, two (2) o-rings, and five (5) set screws, provide (4) new hose clamps and an allen wrench.
PSS Type A shaft seal is a mechanical seal. The sealing surface is formed between the plane of the stainless steel rotating rotor and the fixed carbon fiber bearing.
PRODUCT ID: 50857
SKU: NVN-50857
CSKU: CWR-50857
REWRITE: 61968-pss-shaft-joint-1-shaft-3-tubes
MPN: 02- 134-300
UPC: 839662007320
ASIN: B001HBVAGE
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: PSS Shaft Seal 1-¾" Shaft 3" Tube
NAME_EX: PSS SHAFT SEAL 1 3/4" SHAFT 3" TUBE
PTITLE: PSS Shaft Seal 1-¾" Shaft 3" Tube
TYPE: Marine hardware | Shaft Seals
SELLER: PSS Shaft Seal
SPORTING GOODS> P. HOBBYLEIN AIR> NAUTICAL AND WATER SPORTS PSS Shaft Seal 1-¾ Tube "Arbre 3" -02-134-300
Gtags:
GSpecs:
PSS Shaft Seal 1-¾" Shaft 3" Tube Product Description PSS Shaft Seal 1-3/4" Shaft 3" Tube
L Diameter Shaft: 1 -3/4"
Stern tube diameter (D): 3"
Overall length (A): 9.175"
Total length (compressed) (Compressed A): 8.175"
Rotor diameter (B): 3.75"
Carbon Sleeve Diameter (C): 3.25"
Rear Cuff Length (E): 2"
The Gasket PSS Shaft Sealis the best-selling marine mechanical seal worldwide and is fitted as standard equipment by many of the world's leading boat builders/yards. The PSS Shaft Seal is also recognized. as the first retrofit seal (aftermarket) certified by Bureau Veritas, ABS & Rina: Boat builders/yards recognize the benefits and value of installing PSS as it eliminates maintenance, constant adjustment. and the cost associated with the cable glands ttraditional. PSS Shaft Sealhelps eliminate water in the bilge (100% waterproof) and wear on the propeller shaft. The PSS shaft seal
can be easily retrofitted and is available for shafts ranging from 3/4"
(20 mm) to 6" (150 mm).
The PSSshaft seal is a mechanical seal created between the flat surfaces of the rotating stainless steel rotor and the fixed carbon flange. The carbon fixed bridle is attached to the ship's stern tube with hose clamps and the carbon bridle is attached to the front of the bellows with hose clamps. The stainless steel rotor is mounted on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is attached to the shaft with set screws. This compression (preload) maintains contact between the faces and allows the
PSS to compensate for the thrust of the propeller. The carbon flange is reamed larger than the diameter of the arbre, which allows it to "float" around the shaft diameter and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two O-rings which are recessed into the collar bore. These O-rings rotate with the stainless steel shaft and rotor and experience no wear during operation.
**As with any rubber hose below the waterline, the PSS bellows must be inspected on a regular basis for any signs of wear, aging or chemical deterioration.
PYI suggests, as preventative maintenance, that the PSS bellows be replaced every six years. When replacing the bellows, it is recommended to also replace the stainless steel rotor O-rings and adjustment screws. Sulfuric acid vapors will accelerate the deterioration of rubber, as will an ozonator.
Maintenance kit includes itemsnts you need to properly maintain your PSS shaft seal. Kit includes one (1) PSS boot, two (2) O-rings, five (5) set screws, four (4) new hose clamps and one Allen key.
PSS Type A shaft seal is a mechanical seal. The sealing surface is formed between the plane of the stainless steel rotating rotor and the fixed carbon fiber bearing.
PSS Shaft Seal, 1-¾" Shaft, 3" Tube Related ProductsPSS Shaft Seal Service Kit, 1 3/4" Shaft, 3" Tube
Frequently Asked Questions (FAQ) About PSS Shaft Seal 1-¾" Shaft 3" Tube Who is PSS Shaft Seal?
How to describe the seal PSS Shaft Seal 1-¾" Shaft 3" Tube?
Who is the PSS Shaft Seal? The PSS Shaft Seal is the best-selling marine mechanical seal in the world and is installed as standard equipment by many of the most popular shipyards and boat builders.uted in the world. The PSS Shaft Seal is also recognized as the leading retrofit (aftermarket) seal in the global market.Cribe PSS Shaft Seal 1-¾" Shaft 3" Tube? Type A PSS shaft seal is a mechanical end seal. The sealing surface is formed between the plane of the stainless steel rotating rotor and the fixed carbon fiber bearing.
Save $70 when you purchase the PSS Shaft Seal 1-¾" Shaft 3" Tube for only $554 at NVN Marine! Free same day delivery before 3 p.m. PSS Shaft Seal 1-¾" Shaft 3" Tube Videos PSS Shaft Seal 1-¾" Shaft 3" Tube Technical Specifications
| Type: | Marine Equipment | Shaft Seals |
|---|---|
| Supplier: | PSS Shaft Seal |
| Weight: | 5.5 lbs |
| Product Brochure: | Download the PDF |
| Installing theproduct: | Download PDF |
| Shipping Weight: | 5.5 lbs |
|---|---|
| Box Sizes: | 6.00 (h) x 7.00 (w) x 12.00 (w) |
| Cubic feet: | 504.0 |
| Returnable: | Yes |
For detailed shipping terms, please see our shipping policy shipping and you can find our return and refund policy here.
