PSS Shaft Seal 2" Shaft 2-¾" Tube Marine Hardware
PSS Shaft Seal, 2" Shaft, 2-3/4" TubeShaft Diameter: 2"
Stern tube diameter (D): 2-3/4" to 2-7/8"
Overall length (A): 9.175"
Total length (compressed) (Compressed A): 8.175"
Rotor diameter (B): 3.75"
Rotor diameter carbon cuff (C): 3.25"
Rear cuff length (E): 2"
PSS shaft seal is the best-selling marine mechanical seal worldwide and is fitted as standard equipment by many of the world's most renowned boat builders/yards. PSS shaft seal is also recognized as the leading retrofit (aftermarket) seal in the global market. Certified by Bureau Veritas, ABS and Rina: Boat builders/yards recognize the benefits and value of installing PSS as it eliminates the maintenance, constant adjustment and cost associated with traditional cable glands. Besides theseadvantages, PSS shaft seal helps eliminate water in the bilge (100% waterproof) and water.r to the propeller shaft. The PSS shaft seal
can be easily retrofitted and is available for shafts ranging from 3/4"
(20 mm) to 6" (150 mm).
The PSSshaft seal is a mechanical seal created between the flat surfaces of the rotating stainless steel rotor and the fixed carbon flange. The carbon fixed bridle is attached to the ship's stern tube with hose clamps and the carbon bridle is attached to the front of the bellows with hose clamps. The stainless steel rotor is mounted on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is attached to the shaft with set screws. This compression (preload) maintains contact between the faces and allows the
PSS to compensate for the thrust of the propeller. The carbon flange is reamed larger than the diameter of the lshaft, which allows it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two O-rings which are recessed into the collar bore. These O-rings rotate with the stainless steel shaft and rotor and experience no wear during operation.
**As with any rubber hose below the waterline, the PSS bellows must be inspected on a regular basis for any signs of wear, aging or chemical deterioration.
PYI suggests, as preventative maintenance, that the PSS bellows be replaced every six years. When replacing the bellows, it is recommended to also replace the stainless steel rotor O-rings and adjustment screws. Sulfuric acid vapors will accelerate the deterioration of rubber, as will an ozonator.
Maintenance kit includes itemsyou need to properly maintain your PSS shaft seal. Kit includes one (1) PSS. Below, two (2) O-rings, and five (5) sets of screws, four (4) new hose clamps and an Allen key.
PSS Type A shaft seal is a mechanical seal. The sealing surface is formed between the plane of the stainless steel rotating rotor and the fixed carbon fiber bearing.
PRODUCT ID: 50860
SKU: NVN-50860
CSKU: CWR-50860
REWRITE: 61971-pss-shaft-joint-2-shaft-2-tubes
MPN: 02- 200-234
UPC: 839662007450
ASIN:
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: PSS Shaft Seal 2" Shaft 2-¾" Tube
EX_NAME: PSS SHAFT SEAL 2" SHAFT 2 3/4" TUBE
PTITRE: PSS Shaft Seal 2" Shaft 2-¾" Tube
TYPE: Marine hardware | Shaft Seals
SELLER: PSS Shaft Seal
SPORTING GOODS> OUTDOOR RECREATION> BOATING & WATER SPORTS
2" Dia Shaft Seal, PSS, for 3" Stern Tube
Gtags:
GSpecs:
PSS Shaft Seal, 2" Shaft, 2-¾" Tubing Product Description PSS Shaft Seal, 2" Shaft, 2-3/4" Tubing
Shaft Diameter: 2"
Stern Tube Diameter (D): 2-3/4" to 2-7/8"
Total length (A): 9.175"
Total length (compressed) (Compressed A): 8.175"
Rotor diameter ( B): 3.75"
Carbon cuff diameter (C): 3.25"
Rear cuff length (E): 2"
PSS Shaft Seal is the best-selling marine mechanical seal product worldwide and is installed as standard equipment by many boat builders/yards among the most famous in the world. PSS shaft seal is also recognized as the leading retrofit (aftermarket) seal in the global market. Certified by Bureau Veritas, ABS and Rina: Boat builders/yards recognize the benefits and value of installing PSS as it eliminates maintenance, constant adjustment and cost associated with traditional cable glands. Besides these benefits, the PSSshaft seal helps eliminate water in the bilge (100% waterproof) and wear on the propeller shaft. The PSS shaft seal
can be easily retrofitted and is available for shafts ranging from 3/4"
(20 mm) to 6" (150 mm).
The PSSshaft seal is a mechanical seal created between the flat surfaces of the rotating stainless steel rotor and the fixed carbon flange. The carbon fixed bridle is attached to the ship's stern tube with hose clamps and the carbon bridle is attached to the front of the bellows with hose clamps. The stainless steel rotor is mounted on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is attached to the shaft with set screws. This compression (preload) maintains contact between the faces and allows the
PSS to compensateer the thrust of the propeller. The carbon flange is bored larger than the diameter of the shaft, which allows it to "float" around the shaft and thus compensates for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two O-rings which are recessed into the collar bore. These O-rings rotate with the stainless steel shaft and rotor and experience no wear during operation.
**As with any rubber hose below the waterline, the PSS bellows must be inspected on a regular basis for any signs of wear, aging or chemical deterioration.
PYI suggests, as preventative maintenance, that the PSS bellows be replaced every six years. When replacing the bellows, it is recommended to also replace the stainless steel rotor O-rings and adjustment screws. Sulfuric acid vapors will accelerate the deterioration ofu rubber, just like an ozonator.
The maintenance kit includes the items you need to properly maintain your
PSS Shaf.t Joint. Kit includes one (1) PSS boot, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an Allen wrench.
PSS Type A shaft seal is a mechanical seal. The sealing surface is formed between the plane of the stainless steel rotating rotor and the fixed carbon fiber bearing.
PSS Shaft Seal, 2" Shaft, 2-¾" Tube Related ProductsPSS Shaft Seal Service Kit, 2" Shaft, 2 3/4" Tube
Frequently Asked Questions (FAQ) About PSS Shaft Seal, 2" Shaft, 2-¾" Tube Who is PSS Shaft Seal?
How to describe the PSS shaft seal, 2" shaft, 2-¾" tube?
Who is the PSS shaft seal? ? The PSS shaft seal is the best-selling marine mechanical seal in the world and is installed in equStandard equipment by many of the world's leading shipyards and boat builders. PSS Shaft Seal is also recognized as the leading retrofit (aftermarket) seal in the global market.How to Describe PSS Shaft Seal, 2" Shaft, 2-¾ Tube "? Type A PSS shaft seal is a mechanical end seal. The sealing surface is formed between the plane of the stainless steel rotating rotor and the fixed carbon fiber bearing.
Save $146 when you purchase the PSS Shaft Seal 2" Shaft 2-¾" Tube for only $587 from NVN Marine! Free same day delivery before 3 p.m. PSS Shaft Seal 2" Shaft 2-¾" Tube Videos PSS Shaft Seal 2" Shaft 2-¾" Tube Technical Specifications
| Type: | Marine Equipment | Shaft Seals |
|---|---|
| Supplier: | PSS Shaft Seal |
| Product brochure: | Download PDF |
| Product installation: | Download PDF |
