Uncut NavPod GP1900 SailPod (Usable Face = 12.5"L x 7.8"H) (12.5" W x 7.8" H) f/9.5" Wide Guard Boat Outfitting

GP1900 Uncut SailPod (usable face = 12.5" width x 7.8" height) (31.8 cm width x 1
9.8 cm height) for 9. 5" wide

SailPods are intended for mounting a single radar or chartplotter at the helm. Navigation at your fingertips. "Where you need it...when you need it." clearly see the fine details of the screen. NavPods have a high-gloss finish, giving you a clean mounting solution while hiding unsightly wires. Nickel-chrome-plated tamper-proof screws provide a little bling and lots of security. Designed with a double-seal waterproof seal NavPods protect your electronic devices from the harshest offshore sailing conditions. It is best to mount a SailPod on a single-curvature AngleGuard or use a double-curvature AngleGuard. to install an InstrumentPod on the upper vertical section and a SailPod below on the seinclined ction.

Structural rigidity
Gen3 improvements now include an acrylic-coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially harmful effects on plastic. These NavPods are really strong!

Waterproof seal
All NavPods are made with a double seal system providing an excellent seal between the front and back of the NavPod. This seal offers the best protection for your marine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen3 improvements include an updateThicker silicone outer int with improved flush fit. The internal Poran Microcell polyurethane seal is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel
We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. For the NavPod Gen3 we provide tamper proof nickel plated chrome stainless steel screws for added security combined with a little bling!

Commitment to quality
We are committed to produce high quality waterproof enclosuresé for Marine electronics. We stand behind our commitment by offering a 10-year warranty on all new NavPod Gen3s. We want you to be a NavPod customer for life and are ready to earn your trust and loyalty.

SailPods for Power are intended to be fitted to an SK135 hitch kit and can be used to mount a SailPod on a flat surface, such as the flybridge. Stachion kits can also be used with a SailPod for high mount applications.

GP1900 Uncut SailPod (usable area = 12.5" L x 7.8" H) (31.8 cm W x 1 9.8 cm H), suitable for SailPods protective covers of 9, 5" wide for mounting a single radar or chartplotter on the helmet.. Navigation..
PRODUCT ID: 63799
SKU: NVN-63799
CSKU: CWR-63799
REWRITE: 74910-navpod-gp1900-sailpod-uncut-usable-face
MPN: GP1900
UPC: 659988110777
ASIN: B0753J1R5M
WSKU: NAVGP1900
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: NavPod GP1900 Uncut SailPod (usable face = 12.5" W x 7.8" H) (31.8 cm W x 19.8 cm H) f/9.5" Wide Guard
NAME_EX: NAVPOD SAILPOD UNCUT (USABLE FACE = 12.5" W (usable face = 12.5"L x 7.8"H) (31.8cm W x 19.8cm H) f/9.5" Wide Guard
TYPE: Oat Outfitter | Oat Holders display
SELLER: NavPod
ELECTRONICS> MARINE ELECTRONICS NAVPOD Gp1900 sailpod uncut usable face = 12.5 inches W x 7, 8 inches h 31.8 cm

Gtags:

Boat

GSpecs:

Uncut NavPod GP1900 SailPod (Usable Face = 12.5" L x 7.8" H) (12.5" W x 7.8" H) f/9.5" Wide Guard Product Description GP1900 SailPod Uncut (usable face = 12.5" W x 7.8" H) (12.5" W x 3.8" H) for 9.5" wide protection b>

SailPods are intended for mounting a single radar or chartplotter at the helm. Navigation at your fingertips. "Where you need it…when you need it." Sail Pods are the smart solution for mounting your radar or chartplotter to the helm where you can easily operate it and clearly see small details on the screen. NavPods have a high-gloss finish, giving you a clean mounting solution while hiding unsightly wires. Nickel-chrome plated tamper-resistant screws provide a little bling and a lot of security. Designed with a double-sealed waterproof seal, NavPods protect your electronic devices from boating conditions.on the most difficult and wet offshore. It is best to mount a SailPod on a single-bend AngleGuard or use a double-bend AngleGuard to mount an InstrumentPod on the top physical section and SailPod below on the angled section.

Structural Rigidity
Gen3 enhancements now include thicker gauge acrylic coated ABS material which improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially harmful effects on plastic. These NavPods are really strong!

Waterproof seal
All NavPods are made with a double j systemointed providing an excellent seal between the front and back of the NavPod. This seal offers the best protection for your marine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen3 improvements include a thicker silicone outer seal with an improved f.lush fit. The Poran Microcell Polyurathane internal seal is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel
We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our NavPodhe traditional series. For the NavPod Gen3 we provide tamper proof nickel plated chrome stainless steel screws for added security combined with a little bling!

Commitment to quality
We are committed to produce high quality waterproof enclosures for marine electronics. We stand behind our commitment by offering a 10-year warranty on all new NavPod Gen3s. We want you to be a NavPod customer for life and ready to earn your trust and loyalty.

SailPod for Power is intended for mounting on a Stachion SK135 kit and can be used to mount a SailPod to a surface plane, such as the flybridge. Stachion kits can also be used with a SailPod for high mount applications.

GP1900 Uncut SailPod (usable area = 12.5" L x 7.8" H) (31.8 cm W x 1 9.8 cm H), suitable for SailPods protective covers of 9, 5" wide for mounting a single radar orchartplotter on the helmet. Navigation..

Frequently asked questions (FAQ) about the NavPod GP1900 Uncut SailPod (usable face = 12.5" width x 7.8" depth height) (31.8 cm width). (31) .8 cm L x 19.8 cm H) f/ 9.5" wide protection?
Is it cut or uncut?
How to mount or what is the mounting style of the NavPod GP1900 Uncut SailPod (Usable Face = 12.5" L x 7.8" H) (12.5" W x 7.8" H) f/9.5" Lide Guard? What size is the usable surface area of the product?
Who is the NavPod? Navpod is a better way to mount your fish finder, radar or GPS The unique waterproof seal, build quality and attractive design make the instrument case the best. built never before available for the maritime industry Features of all Navpods included.Features waterproof silicone gasket, tamper-resistant fasteners for added security and convenience, concealed wiring and clean installation for easy access. How to describe the uncut NavPod GP1900 SailPod (usable face = 12.5" W x 7.8" H) (12.5" W x 7.8" H) f/9.5" Wide Guard? GP1900 Uncut SailPod (usable area = 12.5" L x 7.8" H) (12.5" W x 3.8" H), fits 9.5" wide SailPods protective cover for mounting a single radar or chartplotter on the helmet. Navigation. ..Is it cut or uncut? Uncut How to mount or what is the mounting style of the Uncut NavPod GP1900 SailPod (Usable Face = 12.5"L x 7.8"H) (12.5"L x 7.8"H) cm H) f/9.5" Wide guard? PedestalHow big is the usable surface area of the product? 12.4"L x 7.4"H

Save $99 when you purchase the uncut NavPod GP1900 SailPod (usable face = 12.5"L x 7.8"H) (31.8 cm W x 19.8 cm H) f/9.5" Wide Guard for only $320 at NVN Marine! Same day shipping before 3 p.m. NavPod GP1900 SailPod no cut (usable face = 12.5" W x 7.8" H) (12.5" W x 7.8" H) f/9.5" Wide Guard Technical Specifications

Type:	Boat Equipment \| Display Stands
Supplier:	NavPod
Cut/Uncut:	Uncut
Mounting Style:	Pedestal
Usable Side:	12.4"L x 7.4"H

NavPod GP1900 Uncut SailPod (usable face = 12.5"L x 7.8"H) (31.8cm W x 19.8cm H) f/9.5" Wide Guard User ReviewsNavPod GP1900 Uncut SailPod (Usable Face = 12.5"W x 7.8"H) (31.8 cm L x 19.8 cm H) f/9.5" Wide Guard Shipping & Return

For detailed shipping policy, please see our Shippingtion Policy and you can find our Return and Refund Policy here.