Victron isolation transformer - 2000 W - 115/230 VAC Electrical

Isolation transformer - 2000 W - 115/230 VAC

Safety and prevention of galvanic corrosion The isolation transformer eliminates any electrical continuity between the power supply at the dock and the boat. It is essential for safety and eliminates the need for galvanic isolators and polarity alarms.

Safety is taken for granted in the case of a normal land installation. A fuse will blow or a GFCI (Ground Fault Current Interrupter) will trip in the event of a short circuit or current leak to ground. Connecting the shore power ground wire to the metal parts of the boat will result in galvanic corrosion (see below). Bringing only the hot and neutral wires on board results in a dangerous situation because the GFCIs will not work and a fuse will not blow if there is a short to a metal part of the boat.

Galvanic corrosion occurs whentwo different metals in electrical contact are simultaneously exposed to an electrically conductive fluid. Sea water and, to a lesser extent, fresh water are such fluids. In general, the more active alloy of the pair corrodes preferentially while the less active (more noble) material is cathodically protected. The rate of galvanic corrosion is a function of several variables, including surface area ratios, fluid conductivity, temperature, nature of materials, etc.

It is a mistake to believe that galvanic corrosion only occurs in metal and aluminum hulls. . In fact, this can happen on any boat as soon as a metal part (the shaft and the propeller) comes into contact with water. Galvanic corrosion will quickly dissolve your sacrificial anodes, and attack the shaft, propeller and other metal parts in contact with water as soon as the boat is connected to the al network.dockside feeding. It may therefore be tempting not to connect the ground conductor: this is, however, extremely dangerous because the GFCIs will not work and a fuse will not blow in the event of a short on a metal part of the boat.

The best solution to avoid galvanticorrosion and at the same time prevent any dangerous situation is to install an isolation transformer to connect to shore power.

The isolation transformer eliminates any electrical continuity between shore power and the boat. Shore power is supplied to the primary side of the transformer and the vessel is connected to the secondary. The isolation transformer completely isolates the boat from the shore. By connecting all metal parts to the neutral output on the secondary side of the transformer, a GFCI will trip or fuse will blow in the event of a short circuit.

Soft start is a standard feature ofa Victron Energy isolation transformer. This will prevent the shore power fuse from blowing due to transformer inrush current, which would otherwise occur

Warranty Information

This product can expose you to chemicals known to the State of California .lifornia to cause cancer, birth defects, or other reproductive harm. For more information, go to P65Warnings.ca.gov.

Please contact your dealer for returns, repairs. or support issue related to this product.

Essential in a professional marine energy system It can prevent electrolytic corrosion, and more importantly, it can be used as a device to ensure safety. of the electrical system. Ring winding...
PRODUCT ID : 82997
SKU: NVN-82997
CSKU: CWR-82997
REWRITE: 94108-victron-insulation-transformer-2000w-115-230
MPN: ITR040202041
UPC: 8719076022480
ASIN: B078RD2SQX
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: Victron Isolation transformer - 2000W - 115/230 VAC
NOM_EX: VICTRON ISOLATION TRANSFORMER 2000W 115/230V
PTITRE: Victron isolation transformer - 2000W - 115/230 VAC
TYPE: Electric | Shore Power
SUPPLIER: Victron Energy
VEHICLES & PARTS> VEHICLE PARTS & ACCESSORIES> WATERCRAFT PARTS & ACCESSORIES
BISS Basic

Google Title : Victron Insulation Transformer 2000w 115230 Vac by Hodges Marine
BISS Basic
Gtags:

Victron Energy
Transformer
Transformer Isolation

GSpecs:

Victron isolation transformer - 2,000 W - 115/230 VAC Product description

Isolation transformer - 2,000 W - 115/230 VAC

Safety and prevention galvanic corrosion The isolation transformer eliminates any electrical contact continuity between shore power and the boat. It is essential for safety and eliminates the need for galvanic isolators and polarity alarms.

Galvanic corrosion occurs when two dissimilar metals in electrical contact are simultaneously sneakily exposed to an electrically conductive fluid. Seawater and, to a lesser extent, fresh water are such fluids. In general, the more active alloy of the pair corrodes preferentially while the less active (more noble) material is cathodically protected. The rate of galvanic corrosion is a function of several variables, including surface area ratios, fluid conductivity, temperature, nature of materials, etc.

It is a mistake to believe that galvanic corrosion only occurs in metal and aluminum hulls. . In fact, this can happen on any boat as soon as a metal part (the shaft and the propeller) comes into contact with water. Galvanic corrosion will quickly dissolve your sacrificial anodes, and attack the shaft, propeller and other partss metal in contact with water as soon as the boat is connected to the shore power network. It may therefore be tempting not to connect the ground conductor: this is, however, extremely dangerous because GFCIs will not work and a fuse will not blow in the event of a short circuit to a metal part on the boat.

The best solution to avoid galvanic corrosion and at the same time prevent any dangerous situation is to install an isolation transformer to connect to shore power.

Soft start is a standard feature of a Victron Energy isolation transformer. This will prevent the shore power fuse from blowing due to transformer inrush current, which would otherwise occur.

Warranty Information

WARNING :This product can expose you to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information,

Please contact your dealer for any returns, repairs, or support issues related to this product.

Essential in a professional marine energy system. It can prevent electrolytic corrosion, and more importantly, it can be used as a device to ensure the safety of the electrical system. Ring winding...

TransformatVictron isolation switch - 2000 W - 115/230 VAC Related productsVictron battery monitor - BMV-702 - Black
Victron intelligent battery monitor - BMV-712 - Gray - Bluetooth compatible
Victron battery monitor - BMV-702 - Gray
Victron BMV-700 Battery Monitor
Victron BMV-712 Black Smart Battery Monitor

Frequently Asked Questions (FAQ) About of the Victron isolation transformer - 2000 W - 115/230 VAC Who is Victron Energy?
How to describe the Victron isolation transformer - 2000 W - 115/230 VAC?
Who is Victron Energy? Victron Energy is a global company renowned for its technical innovation, reliability and build quality. Victron products, which excel at efficiently combining two or more distinct energy sources, are recognized internationally as the professional choice for resilient energy storage systems. Victron products includesine wave inverters, sine wave inverters/chargers, battery chargers, DC/DC converters, transfer switches, battery monitors and more. How to describe the Victron isolation transformer - 2000 W - 115/230 VAC? Essential in a professional marine energy system. It can prevent electrolytic corrosion, and more importantly, it can be used as a device to ensure the safety of the electrical system. Winding...

Safety is our number one priority.
The isolation transformer eliminates any electrical continuity between shore power and the boat.
Eliminates the need for a battery charger, as it can charge from shore power.

Eliminates continuity between shore power and the boat .
Protects against galvanic corrosion.
Isolation transformer - 2000W - 115/230 VAC

Isolation transformer - 2000W - 115/230 VAC
Safety and prevention of galvanic corrosion
The isolation transformer eliminates any electrical continuity between the shore power and boat. It is essential for safety and eliminates the need for complicated wiring

Save $70 on the purchase of the Transformer Victron Isolator - 2000W - 115/230VACfor only $397 from NVN Marine! Free same day delivery before 3 p.m. Victron isolation transformer - 2000 W - 115/230 VAC Technical specifications

Type:	Electric \| Shore power
Supplier:	Victron Energy
Weight:	30.25 lbs
User Guide:	Download PDF
Product brochure:	Download PDF

Victron isolation transformer - 2000 W - 115/230 VAC User reviewsVictron isolation transformer - 2000 W - 115/230 VAC Shipping & Return

Weight d 'shipping:	30.25 lbs
Box sizes:	9 .00 (h) x 12.00 (w) x 18.00 (l)
Cubic feet:	1944.0
P65:	Yes