Victron MultiPlus 12/1200 - 50-16 - 120V - VE. Bus Electrical

MultiPlus 12/1200 - 50-16 - 120V - VE. Bus

The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger with adaptive charging technology, and a high-speed AC transfer switch in one compact package. In addition to these main functions, the MultiPlus has several advanced features, described below.

Parallel operation and three-phase capacity

Up to six Multis can work in parallel to achieve higher output power. In addition to parallel connection, three units can be configured for three-phase output.

PowerControl - Manage limited generator power, shore side or grid power

With the multiple control panel, maximum generator or mains current dock can be defined. The MultiPlus will then take into account other AC loads and use whatever is supplementedmentary for charging, thus preventing the generator or shore power from being overloaded.

PowerAssist - Increase the capacity of Shore or generator power

This feature takes the principle of PowerControl to an additional dimension. It allows MultiPlus to supplement the capacity of the alternative source. Where peak power is often only required for a limited period, the MultiPlus will ensure that insufficient power from the dock or generator is immediately compensated by battery power. When the load is reduced, the available energy is used to recharge the battery.

Four-stage adaptive charger and two-bank battery charging

The main output provides powerful charging to the battery system using advanced "adaptive charging" software. The software adjusts the three-step automatic process based onbattery status and adds a fourth stage for long periods of trickle charging. The adaptive charging process is described in more detail on the charger data sheet and on the Victron website under Technical Information. Additionally, the MultiPlus will charge a second battery. Try using an independent trickle charge output intended for a prime mover or generator starting battery.

High starting power

It is necessary to start high demand loads such as power converters for LED lamps, halogen lamps or power tools .

Search mode

When search mode is activated, the power consumption of the inverter in no-load operation is reduced by approx. 70%. In this mode, the Multi, when operating in inverter mode, turns off in case of no or very low load and turns on every two secondsfor a short period. If the output current exceeds a set level, the inverter will continue to operate. Otherwise, the inverter will turn off again.

Programmable relay

By default, the programmable relay is set as an alarm relay, it i.e. turn off the relay in the event of an alarm or pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low).

Remote on/off/Charger on

Three-pole connector.

On-site system configuration, monitoring and control

After installation, the MultiPlus is ready for operation. Some settings can be changed using DIP switches. 500/800/1200VA models: remote switch/battery charging voltage/inverter frequency/search mode. 1600/2000VA Models: Battery Charging Voltage/Search Mode. For moresettings, use VE-Config or VE. Smart USB key.

Remote setup and monitoring

Install a Cerbo GX or other GX product to connect to the Internet. Operational data can be stored and displayed free of charge on Victron's VRM (Victron Remote Management) website. Once connected to the Internet, systems can be accessed remotely and settings can be changed.

Specifications:

PowerControl: Yes
PowerAssist: Yes
Transfer switch ( A): 16

Inverter specifications:

Input VVoltage range (V DC): 9.5 – 17 V, 19 – 33 V, 38 – 66 V
Output voltage: 230 VAC, ± 2% / Frequency 50 Hz ± 0.1%
Continuous output power at 25°C (VA): 1200
Continuous output power at 25°C (W): 1000
Continuous output power at 40°C (W): 900
S powercontinuous nettle at 65°C (W): 600
Peak power (W): 2400
Maximum efficiency (%): 93/94/95%
No-load power (W): 10/9/10 W
No-load power in search mode (W): 3/3/3 W

Charger Specifications:

AC Input: Input Voltage Range: 187-265 VAC / Input Frequency: 45-65 Hz
Absorption charging voltage (V DC): 14.4 / 28.8 / 57.6
Floating charging voltage (V DC): 13.8 / 27.6
Storage mode (V DC): 13.8 / 27.6 / 55.2
House battery charging current (A): 50 / 25 / 13 A
Starting battery charging current (A): 1A (12V and 24V models only)
Battery temperature sensor: Yes

General specifications:

Programmable relay: Yes (1x)
Protection: a - g
VE.Bus communication port: For parallel and three-phase operationase, remote monitoring and system integration (ASS030065510 RJ45 splitter required for 500/800/1200 VA models)
Remote on/off: on/off/charger only
DIP Switches: Yes
Internal DC Fuse: 200/100/50 A
Operating Temperature Range: -40 - +65°C / -40 to 150°F ( fan-assisted cooling ), Humidity (non-condensing) max 95%

Case Specifications:

Common Features: Material and color: aluminum (blue RAL 5012) / Protection category: IP 21
Battery-Connection: 35 / 25 / 10 mm²
230 V AC-Connection: G-ST18i connector
Weight: 8.2 kg
Dimensions (H x W x D): 406 x 250 x 100 mm / 15.98 x 9.84 x 3.94 inches.

Standards:

Safety: EN-IEC 60335-1, EN-IEC 60335-2-29, EN 62109- 1
Emission, immunity: EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
Automotive Directive: ECE R10-5
Can be set to 60 Hz and 240 V
Protection: Output short circuit, Overload, Battery voltage too high, Battery voltage too low, Temperature too high, 230VAC on inverter output, voltage ripple input too high
Non-linear load, 3:1 crest factor
A programmable relay that can be set for a general alarm, DC undervoltage or generator start/stop signal function, AC rating: 230V/4A, DC rating: 4A up to 35VDC, 1A up to 60VDC
Remote charging voltage/battery/inverter frequency/search mode
Battery charging voltage/power modesearch

Please contact your reseller for any returns, repairs, or support issues related to this product.

PRODUCT ID: 103416
SKU: NVN-103416
CSKU: CWR-103416
REWRITE: 114527-victron-multiplus- 12-1200-50-16-120v
MPN: PMP122120100
UPC:
ASIN:
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: VICTRON MULTIPLUS 12/1200 50-16 120V VE.BUS
NAME_EX:
PTITLE: Victron MultiPlus 12/1200 - 50-16 - 120V - VE. Bus
TYPE: Electric | Charger/Inverter Combos
SELLER: Victron Energy
ELECTRONICS> ELECTRONIC ACCESSORIES> POWER

Gtags:

GSpecs:

Victron MultiPlus 12/1200 - 50-16 - 120V - VE. Product description Bus

MultiPlus 12/1200 - 50-16 - 120V - VE. Bus

Parallel operation and three-phase capacity

Up to six Multis can work in parallel to achieve higher output power. In addition to parallel connection, three units can be configured for three-phase output.

PowerControl - Manage limited generator power, shore side or grid power

With the multiple control panel, maximum generator or mains current dock can be defined. The MultiPlus will takethen takes into account other AC loads and will use whatever is extra for loading, thus preventing the generator or shore power from being interrupted.

PowerAssist - Increase the capacity of shore power or generator

Four-stage adaptive charger and two-bank battery charging

The main output provides powerful charging to the battery system using advanced "charge a" softwareadaptive". The software adjusts the automatic three-stage process based on battery condition and adds a fourth stage for long periods of trickle charging. The adaptive charging process is described in more detail on the charger data sheet and on the Victron website under Technical information.training. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starting battery.

High starting power

It is necessary to start high demand loads such as power converters for LED lamps, halogen lamps or power tools .

Search mode

When search mode is activated, the power consumption of the inverter in no-load operation is reduced by approx. 70%. In this mode, the Multi, when operating ininverter mode, turns off at no or very low load and turns on every two seconds for a short time. If the output current exceeds a set level, the inverter will continue to operate. Otherwise, the inverter will turn off again.

Programmable relay

By default, the programmable relay is set as an alarm relay, it that is, the relay will turn off in the event of an alarm or pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low).

Remote on/off/Charger on

Three-pole connector.

On-site system configuration, monitoring and control

After installation, the MultiPlus is ready for operation. Some settings can be changed using DIP switches. 500/800/1200VA models: remote switch/battery charging voltage/ond frequencySearch color/mode. 1600/2000VA Models: Battery Charging Voltage/Search Mode. For more settings, use VE-Config or the VE. Smart USB key.

Remote setup and monitoring

Specifications:

PowerControl: Yes
PowerAssist: Yes
Transfer switch ( A ): 16

Inverter specifications:

Input voltage range (V DC): 9 .5 – 17 V, 19 – 33 V, 38 – 66 V
Output voltage: 230 VAC, ± 2% / Frequency 50 Hz ± 0.1%
Power of continuous output at 25°C (VA): 1,200
Powercontinuous output power at 25°C (W): 1000
Continuous output power at 40°C (W): 900
Continuous output power at 65°C ( W) ): 600
Maximum power (W): 2,400
Maximum efficiency (%): 93/94/95%
No-load power (W ): 10 / 9 / 10 W
No load power in search mode (W): 3 / 3 / 3 W

Charger specifications:

AC Input: Input Voltage Range: 187-265 VAC / Input Frequency: 45 - 65 Hz
Load Voltage Absorption (V DC): 14.4 / 28.8 / 57.6
Float charge voltage (V DC): 13.8 / 27.6
Storage mode ( V DC): 13.8 / 27.6 / 55.2
Home battery charging current (A): 50 / 25 / 13 A
Charging current of Starter battery (A): 1A (12V and 24V models only)
BatteryStandard temperature sensor: Yes

General specifications:

Programmable relay : Yes (1x)
Protection: a - g
VE.Bus communication port: for parallel and three-phase operation, remote monitoring and system integration (RJ45 splitter ASS030065510 required for 500/800/1200 VA models)
Remote On/Off: On/Off/Charger only
DIP Switches: Yes
Internal DC fuse: 200/100/50 A
Operation Temperature range: -40 - +65°C / -40 to 150°F (fan assisted cooling), humidity (non-condensing) max 95 %

Housing specifications:

Common characteristics: Material and color: aluminum (RAL 5012 blue) / Protection category : IP 21
Battery connection: 35 / 25 / 10 mm²
230 V AC connection: G-ST18i connector
Weight: 8.2 kg
Dimensions (H x W x D): 406 x 250 x 100 mm / 15.98 x 9.84 x 3.94 inches.

Standards:

Security: EN-IEC60335-1, EN-IEC 60335-2-29, EN 62109-1
Emission, immunity: EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
Automotive directive: ECE R10-5
Can be adjusted at 60 Hz and 240 V
Protection: Output short circuit, Overload, Battery voltage too high, Battery voltage too low, Temperature too high, 230VAC on inverter output, Power ripple input voltage too high
Non-linear load, 3:1 crest factor
A programmable relay that can be set for general alarm, DC undervoltage or generator start/stop signal function, AC rating: 230V/4A, DC current: 4A up to 35V DC, 1A up to 60 V CC
Tbattery charging voltage/remote/inverter frequency/search mode
Battery charging voltage/search mode

Please contact your reseller for any returns, repairs or support issues related to this product.

Save $85 on purchase. the Victron MultiPlus 12/1200 - 50-16 - 120V - VE. Busfor only $487 from NVN Marine! Free same day delivery before 3 p.m. Victron MultiPlus 12/1200 - 50-16 - 120V - VE. Victron MultiPlus 12/1200 Bus Videos - 50-16 - 120V - VE. Bus technical specifications

Type:	Electric \| Charger/Inverter Combos
Supplier:	Victron Energy
User Guide:	Download PDF
Product Manual:	Download PDF
Product brochure:	DownloadPDF

Victron MultiPlus 12/1200- 50-16 - 120V - VE. Bus user reviewsVictron MultiPlus 12/1200 - 50-16 - 120V - VE. Shipping and return by bus