Victron Skylla-i 24/100 battery charger (3) 230 V battery charger Electrical

Skylla-i 24/100 battery charger (3) 230 V battery charger

The Skylla-i (3) has 3 isolated outputs. All outputs can provide full rated output current.

Features:

Robust - Epoxy powder coated aluminum enclosures with protection Anti-drip and stainless steel fixings resist the rigors of an unfavorable environment: heat, humidity and salt air. The circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if necessary through automatic reduction of output current in extreme environmental conditions.
Flexible: alongside a built-in interface CAN bus (NMEA2000), rotary switch, DIP switches and potentiometers are available to adapt the acharging algorithm to a particular battery and its conditions of use. Please refer to the manual for a complete overview of the possibilities.
Synchronized parallel operation - Multiple chargers can be synchronized with the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP cables. Note: Two-output and three-output chargers cannot be paralleled with each other. Please see the manual for details.
The right amount of charge for a lead acid battery: Variable absorption time - When only superficial discharges occur, the absorption time is kept short to avoid overcharging the battery. After a deep discharge, the absorption time is automatically increased to ensure the battery is fully recharged.
Preventing damage from excessive off-gassing: BatterySafe Mode - Ifyou want to quickly charge a battery, high charging current in In combination with high absorption voltage, the Skylla-i will prevent damage from excessive gassing by automatically limiting the rate of voltage rise once the voltage of gassing achieved.
Less maintenance and aging when the battery is not used: Storage mode - The storage mode activates whenever the battery has not been subjected to discharge for 24 hours. In storage mode, the float voltage is reduced to 2.2 V/cell (26.4 V for a 24 V battery) to minimize gassing and corrosion of the positive plates. Once a week, the voltage is brought back to the absorption level to "refresh" the battery. This feature prevents electrolyte stratification and sulfation, a major cause of early battery failure.
To increase battery life: compensationTemperature sensor - Every Skylla-i comes with a battery temperature sensor. Once connected, the charging voltage will automatically decrease with increasing battery temperature. This feature is particularly recommended for sealed lead acid batteries and/or where significant battery temperature fluctuations are expected.
Battery Voltage Sensing – To compensate for voltage loss due to cable resistance, the Skylla-i comes with a voltage sensing function so that the battery always receives the correct charging voltage.
Suitable for AC and DC power (AC-DC and DC operation -DC) - The chargers also accept a DC power supply.
Use as a power supply - Thanks to the perfectly stabilized output voltage, the Skylla-i can be used as a power supply if batteries or large buffer capacitors do not are not available.
Prêt for Li-Ion (LiFePO4) - Simple on/off control of the charger can be implemented by connecting a relay or opening the optocoupler output from the collector of a Li-Ion BMS to the remote control port of the charger . Alternatively, full voltage and current control can be achieved by connecting to the galvanically isolated CAN bus port.

Specifications:

Input voltage (VAC): 230V
Input voltage range (VAC): 185-265V
Input voltage range (VDC) ): 180-350V
Maximum AC input current at 180 VAC: 20 A
Frequency (Hz): 45-65 Hz
Charging voltage Absorption voltage (VDC): 28.8 V
Float charging voltage (VDC): 27.6 V
Storage charging voltage (VDC): 26 .4V
Charging current (A): 3 x 100A (maximum total output: 100A)
Charging algorithm: 7-step adaptive
Capacity battery capacity: 500-1000Ah
Charging algorithme (LiFePO4): 3 stages, with on-off control or CAN bus control
Temperature sensor: Yes
Power mode: Yes
Port Remote on-off: Yes (can be connected to a Li-Ion BMS)
VE.Can communication port: Two RJ45 connectors, NMEA2000 protocol, galvanically isolated. Built-in 12V CAN bus power supply, 30V DC maximum
Synchronized parallel operation: Yes, with VE.Can
Forced cooling: Yes
Protection: Reverse battery polarity (fuse) / Output short circuit / Overheating
Temp. range: -20 to 60°C (full output current up to 40°C)
Material and color: aluminum (blue RAL 5012)
Battery connection: bolts M8
230 VAC connection: 10 mm² screw clamp (AWG 7)
Protection category: IP21
Weight: 16 lbs. (7 kg)
Dimensions (hxwxd): 405 x 250 x 150 inches (16.0 x 9.9 x 5.9 mm)

Please contact your resoldr for any returns, repairs, or support issues related to this product.

PRODUCT ID: 88886
SKU: NVN-88886
CSKU: CWR-88886
REWRITE: 99997-victron-skylla-i-battery-charger-24-100-3 -230 V
MPN: SKI024100002
UPC:
ASIN:
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: VICTRON SKYLLA-I 24/100 (3) 230 V BATTERY CHARGER
EX_NAME:
PTITLE: Victron Skylla-i 24/100 Battery Charger (3) 230V Battery Charger
TYPE: Electric | Battery Chargers
SELLER: Victron Energy
VEHICLES & PARTS> VEHICLE PARTS & ACCESSORIES> WATERCRAFT PARTS & ACCESSORIES

Gtags:

GSpecs:

Victron Skylla-i 24/100 battery charger (3) 230 V battery charger Product description

Skylla-i 24/100 battery charger (3) 230 V battery charger

The Skylla -i (3) has 3 isolated outputs. All outputs can provide full rated output current.

Features:

Robust - Epoxy powder coated aluminum enclosures with protection Anti-drip and stainless steel fixings resist the rigors of an unfavorable environment: heat, humidity and salt air. The circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if necessary through automatic reduction of output current in extreme environmental conditions.
Flexible: alongside a built-in interface CAN bus (NMEA2000),Rotary switch, DIP switches and potentiometers are available to adapt the charging algorithm to a particular battery and its operating conditions. Please refer to the manual for a complete overview of the possibilities.
Synchronized parallel operation - Multiple chargers can be synchronized with the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP cables. Note: Two-output and three-output chargers cannot be paralleled with each other. Please see the manual for details.
The right amount of charge for a lead acid battery: Variable absorption time - When only superficial discharges occur, the absorption time is kept short to avoid overcharging the battery. After a deep discharge, the absorption time is automatically increased to ensure that the battery is completefully recharged.
Preventing damage from excessive gassing: BatterySafe mode - If you want to quickly charge a battery, a high charging current in In combination with a high absorption voltage, the Skylla- i will prevent damage from excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage is reached.
Less maintenance and aging when the battery is not in use : Storage mode: Storage mode activates whenever the battery has not been subjected to discharge for 24 hours. In storage mode, the float voltage is reduced to 2.2 V/cell (26.4 V for a 24 V battery) to minimize gassing and corrosion of the positive plates. Once a week, the voltage is brought back to the absorption level to "refresh" the battery. This feature prevents electrolyte stratification and sulfation, a major cause ofearly battery failure.
To increase battery life: Temperature compensation - Every Skylla-i comes with a battery temperature sensor. Once connected, the charging voltage will automatically decrease with increasing battery temperature. This feature is particularly recommended for sealed lead acid batteries and/or where significant battery temperature fluctuations are expected.
Battery Voltage Sensing – To compensate for voltage loss due to cable resistance, the Skylla-i is supplied with a voltage sense installation so that the battery always receives the correct charging voltage.
Suitable for AC and DC power supply (AC-DC and DC- operation DC) - The chargers also accept a DC power supply.
Use as a power supply - Thanks to the perfectly stabilized output voltage, the Skylla-i can be used as a power supplymentation if batteries or large buffer capacitors are not available.
Li-Ion (LiFePO4) ready - Simple on-off control of the charger can be implemented by connecting a relay or optocoupler output open collector from a Li-Ion BMS to the remote control port of the charger. Alternatively, full voltage and current control can be achieved by connecting to the galvanically isolated CAN bus port.

Specifications:

Input voltage (VAC): 230V
Input voltage range (VAC): 185-265V
Input voltage range (VDC) ): 180-350V
Maximum AC input current at 180 VAC: 20 A
Frequency (Hz): 45-65 Hz
Charging voltage Absorption voltage (VDC): 28.8 V
Float charging voltage (VDC): 27.6 V
Storage charging voltage (VDC): 26.4 V
Charging current (A): 3 x 100 A (maximum total output: 100 A)
Charging algorithm: adaptive7-stage
Battery capacity: 500-1000 Ah
Charging algorithm (LiFePO4): 3 stages, with on-off control or CAN bus control
Temperature sensor: Yes
Power mode: Yes
Remote on-off port: Yes (can be connected to a Li-Ion BMS)
VE.Can communication port: Two RJ45 connectors, NMEA2000 protocol, galvanically isolated. Built-in 12V CAN bus power supply, 30V DC maximum
Synchronized parallel operation: Yes, with VE.Can
Forced cooling: Yes
Protection: Reverse battery polarity (fuse) / Output short circuit / Overheating
Temp. range: -20 to 60°C (full output current up to 40°C)
Material and color: aluminum (blue RAL 5012)
Battery connection: bolts M8
230 VAC connection: 10 mm² screw terminal (AWG7)
Protection category: IP21
Weight: 16 lbs. (7 kg)
Dimensions (hxwxd): 405 x 250x 150 in (16.0 x 9.9 x 5.9 mm)

Please contact your dealer for any returns, repairs, or support issues related to this product.

Save $288 when you purchase the Victron Skylla-i 24/100 Battery Charger (3) 230 Battery Charger Vfor only $1,632 from NVN Marine! Free same day delivery before 3 p.m. Victron Skylla-i 24/100 Battery Charger (3) 230 V Battery Charger Technical SpecificationsUser Guide:

Type:	Electric \| Battery chargers
Supplier:	Victron Energy
Charger Input - Voltage:	230 V
Charger Output - Amps:	3 x 100A, 100A maximum
Load banks:	3
Download PDF

Victron Skylla-i 24/100 Battery Charger (3) 230V Battery Charger User ReviewsVictron Skylla-i 24/100 Battery Charger (3) 230V Battery Charger Shipping & Returns

For a policy detailed shipping, please see our shipping policy and you can find our return and refund policy here.