Barton Marine Laser Replica Cunningham Assembly f/Laser Dinghy Sailing

Cunningham Laser Replica Assembly for Laser Dinghy

The Barton Cunningham assembly comes with an 8:1 purchase for those who find the standard system difficult. It is simple to install and easy to use. Components can be configured to be legal.

Contains:

00 Series 0 110 Single Fixed Eye (attached to main red line at through the eye sail)
00 110 Single fixed eye series 0 (attached to secondary yellow line, short tail)
Primary line 0.44 m x 4 mm red dyneema (with loops long and short)
Sub line Yellow line 3.5m x 4mm (large loop with long and short tails)

Assembly instructions:

Step 1:
Before inserting the pole into the slot, slide the large loop of the secondary yellow line onto the base of the pole and locate - it under the tab of the mast kicker.

Stepe 2:Pass the main red line through the Cunningham eye of the sail, then detach the kicker assembly from the boom. Pass the long loop of the main red line over the entire kicker assembly so that the loop lies against the mast and in front of the kicker base plate.

Step 3:Reattach kicker assembly in boom. Pass the long tail of the secondary yellow line through the block attached to the short tail on the secondary yellow line. This long tail now continues up to the base block of the mast and back to the base of the control line cleat. To detach after sailing, remove the yellow secondary line from the cleat base and mast base block. Detach the kicker from the boom and pass the long loop of main line over the kicker assembly and remove it.

Pass the main line through the cunningham eye of the sail.

Barton fittings are replacementsHigh quality acements that perform the same function as the original part. They should not be confused with official parts bearing the Laser trademark. They cannot be used if you are sailing at an Association event. However, they are perfect for social sailing, sailing schools, club sailing or training. Laser is a registered trademark owned by Velum Limited and currently used under license in Europe by Laser Performance (Europe) Limited.

Barton Marine Equipment Limited is completely independent of Laser Performance (Europe) Limited and Velum Limited . .

The Barton Cunningham Conference purchased these products at an 8:1 price for those who find the standard system difficult to use. It is easy to install and use. Components can be configured as...
PRODUCT ID: 66895
SKU: NVN-66895
CSKU: CWR-66895
REWRITE: 78006-barton-marine-laser-replica-cunningham-assembly- f-laser
MPN: 98,079
UPC: 5035088980796
ASIN: B076DW59YC
WSKU:
SSKU:
KSKU:
GSKU:
MSKU :
LSKU:
NAME: Marine Laser Replica Barton Cunningham Assembly f/Laser Dinghy
NAME_EX: MARINE REPLICA BARTON CUNNINGHAM ASSEMBLY FOR LASER
PTITLE: Barton Marine Laser Replica Cunningham Assembly f/Laser Dinghy
TYPE: Sailing | Blocks
SELLER: Barton Marine
VEHICLES & PARTS> VEHICLE PARTS & ACCESSORIES> WATERCRAFT PARTS & ACCESSORIES> SAILBOAT PARTS
Sports
Barton Marine Laser Replica Cunningham Assembly f/Laser Dinghy
Barton Marine Laser Replica Cunningham Assembly f/Laser Dinghy - 98 079
Sports
Gtags:

GSpecs:

Barton Marine Laser Replica Cunningham Assembly f/Laser Dinghy Product Description

Laser Replica Cunningham Assembly f/Laser Dinghy

The Barton Cunningham Assembly comes with purchase 8: 1 for those who find the standard system difficult. It is simple to install and easy to use. Components can be configured to be legal.

Contains:

00 Series 0 110 Single Fixed Eye (attached to main red line at through the eye sail)
00 110 Single fixed eye series 0 (attached to secondary yellow line, short tail)
Primary line 0.44 m x 4 mm red dyneema (with loops long and short)
Sub line Yellow line 3.5m x 4mm (large loop with long and short tails)

Assembly instructions:

Step 1:
Before inserting the pole into the slot, slide the large loop of the secondary yellow line onto the basea mast and locate it under the tab of the mast kicker.

Step 2:Pass the main red line ugh the eye of the Cunningham sail, then detach the boom kicker assembly. Pass the long loop of the main red line over the entire kicker assembly so that the loop lies against the mast and in front of the kicker base plate.

Step 3:

strong>
Reinstall the kicker assembly into the boom. Pass the long tail of the secondary yellow line through the block attached to the short tail on the secondary yellow line. This long tail now continues up to the base block of the mast and back to the base of the control line cleat. To detach after sailing, remove the yellow secondary line from the cleat base and mast base block. Detach the kicker from the boom and pass the long loop of main line over the kicker assembly and remove it.

Pass the main line through travers the sail's cunningham eye.

Barton fittings are high quality replacements that perform the same function as the original part. They should not be confused with official parts bearing the Laser trademark. They cannot be used if you are browsing in an Association event. However, they are perfect for social sailing, sailing schools, sailing clubs or training. Laser is a registered trademark owned by Velum Limited and currently used under license in Europe by Laser Performance (Europe) Limited.

Barton Marine Equipment Limited is completely independent of Laser Performance (Europe) Limited and Velum Limited . .

The Barton Cunningham Conference purchased these products at an 8:1 price for those who find the standard system difficult to use. It is easy to install and use. Components can be configured as...

Frequently asked questionstions (FAQ) about the Barton Marine Laser Replica Cunningham Assembly f/Laser Dinghy Who is the Barton Marine?
How to describe Barton Marine Laser Replica Cunningham Assembly f/Laser Dinghy?
Who is the Barton Navy? Barton continually strives to offer the highest quality products, made from high quality materials, at realistic and affordable prices.ng. New products are constantly designed and developed. Barton is proud of the fact that over 95% of its products are manufactured in Whitstable, allowing Barton to always guarantee high quality. How to describe the Barton Cunningham Assembly f/Laser Dinghy marine laser replica? The Barton Cunningham Conference purchased these products at an 8:1 price for those who find the standard system difficult to use. It is easy to install and use. Components can be configured as...

Save $11 when you purchase the Barton Marine Laser Replica Cunningham Assembly f/Laser Dinghyfor only $33 from NVN Marine! Same day dispatch before 3 p.m. Barton Marine Laser Replica Cunningham Assembly f/Laser Dinghy Technical Specifications

Type:	Sail \| Blocks
Seller:	Barton Marine
Weight:	0.4 lbs

Barton Marine Laser Replica Cunningham Assembly f/Laser Dinghy User ReviewsBarton Marine Laser Replica Cunningham Laser Dinghy Assembly Shipping & Returns

Shipping Weight:	0.4 lbs
Box sizes:	1.00 (h) x 8.00 (w) x 12.00 (w)
Cubic Feet:	96.0
Returnable:	Yes
USPS First Class:	Yes

For moreFor details shipping policy, please see our shipping policy and you can find our return and refund policy here.