NavPod PP4900 Uncut PowerPod (usable face = 12.5"L x 7.8"H) (31.75cm W x 19.8cm H) Boat Outfitting

PP4900 Uncut PowerPod (usable face = 12.5"W x 7.8"H (31 .75 cm L x 19.8 cm H)

PowerPods are designed for the boater serious offshore sailor He demands the most from his boat and electronics He needs a strong and sturdy mount to protect vital electronics from the harshest, yet clean and attractive, offshore sailing conditions. PowerPods are better than bracket mounting. Over 70 pre-cut PowerPods are available for all popular manufacturers' products. The 1.8" opening in the swivel tube provides plenty of room to pass through wires and cables. connectors The PowerPods are positioned at an a.viewing angle tilts backwards by 20 degrees.

PowerPods for Sail are intended to be mounted on a flat surface. Perhaps under the dodger or aft end of the cockpit table, especially on twin wheel boats.

Structural rigidity

Gen3 enhancements now include thicker gauge acrylic-coated ABS material that improves strength and provides best rigicalled structural. This thicker material allows for a greater watertight seal. The better the structural rigidity, the less flex when tightening and more uniform pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially harmful effects on plastic. These NavPods are really powerful!

Waterproof seal

All NavPods are manufactured with a double seal system providing an excellent seal between the front and back of the NavPod. This seal provides the best protection.ction of your marine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The internal Poran Microcell polyurethane seal is now 50% thicker and is not subject to "retentive compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.

Chrome-plated nickel-plated stainless steel

NavPod uses all stainless steel hardwarexydable 316 supplied with each NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. For the NavPod Gen3, we provide tamper-proof nickel-plated stainless steel screws for added security combined with a little bling!

Commitment to quality

We are committed to producing high quality waterproof enclosures for Marine Electronics. We stand by our commitment by offering a 10 year warranty on all new NAs.vPod Gen3. We want you to be a NavPod customer for life and are ready to earn your trust and loyalty.

Compared to rack installation, PowerPods for Power is a better choice. PowerPods have the advantage of having a rotating base, which can provide a sleek appearance for a built-in installation. The latest industry...
PRODUCT ID: 63948
SKU: NVN-63948
CSKU: CWR-63948
REWRITE: 75059-navpod-pp4900-powerpod-uncut-usable-face
MPN: PP4900
UPC: 659988110869
ASIN: B082BB9NKW
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: NavPod PP4900 Uncut PowerPod (Usable Face = 12.5"W width x 7.8" height)
PITTER: Uncut NavPod PP4900 PowerPod (usable face = 12.5" width x 7.8" height) (31.75 cm width x 19.8 cm height) height)
TYPE: Layoutboat entrance | Display Stands
SELLER: NavPod
ELECTRONICS> MARINE ELECTRONICS NavPod PP4900 Uncut PowerPod (usable face = 12.5 " W x 7.8" H) (12.5" W x 7.8" H)

Gtags:

GSpecs:

NavPod PP4900 Uncut PowerPod (Usable Face = 12.5"L x 7.8"H) (31.75cm W x 19.8cm H) Product Description PP4900 Uncut PowerPod (usable side = 12.5"L x 7.8"H (31.75cm W x 19.8cm H)
PowerPods are designed for the serious boater who explodes offshore. He demands the most from his boat and his electronics. He needs a solid and sturdy support to. protect vital electronics from the harshest offshore sailing conditions, yet clean and attractive, PowerPods are better than the mount More than 70 pre-cut PowerPods are available for all products from popular manufacturers. .8" in the swivel tube provides ample spaceto route wires and connectors. The PowerPods are positioned at a 20-degree rearward tilt.
PowerPods for Sail are intended to be mounted on a flat surface Perhaps under the hood or on the side. 'rear of the cockpit table, especially on twin wheel boats.
Structural rigidity
Gen3 improvements now include thicker acrylic gauge Capped ABS material that improves strength and providesbetter structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially harmful effects on plastic. These NavPods are really powerful!
Waterproof seal
All NavPods are manufactured with a double seal system providing an excellent seal between the front and back back of the NavPod. This seal offers the best protection for your electronique marine. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The internal Poran Microcell polyurethane seal is now 50% thicker and is not subject to "retentive compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.
Chrome-plated nickel-plated stainless steel

NavPod uses all 316 stainless steel hardware that comes with every NavPod Large screws.round head tamper proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod For Gen3 NavPods we provide nickel plated stainless steel tamper proof screws for added security combined with a little bling!
Commitment to quality
We are committed to producing high quality waterproof Enclosures for marine electronics . We stand behind our commitment by offering a 10-year warranty on all new NavPod Gen3s. We want you to be a NavPod customer for life and are ready to earn youryour trust and loyalty.

Compared to rack installation, PowerPods for Power are a better choice. PowerPods have the advantage of a rotating base, which can provide a clean appearance for built-in installation...

Frequently asked questions (FAQ) about Uncut NavPod PP4900 PowerPod (usable face = 12.5" width x 7.8" height) (31.75 cm width x 19.8 cm height) Who is the NavPod?
How to describe the NavPod PP4900 PowerPod uncut (usable face = 12.5" L x 7.8" H) (31.75 cm W x 19.8 cm H)?
Is it cut or uncut?
How to mount or what is the mounting style of the uncut NavPod PP4900 PowerPod (usable face = 12.5"L x 7.8"H) (31.75cm W x 19.8cm H)?
How big is the usable surface area of the product?
Who is the NavPod? Navpod is a better way to mount your fishfinder, radar or GPS. The unique waterproof seal, the manufacturing qualityand attractive design make the best-built instrument case ever available to the marine industry. Features of all Navpods include waterproof silicone seal, tamper-proof clips for added security and convenience, concealed wiring and clean installation for easy access. How to describe the uncut NavPod PP4900 PowerPod (usable face = 12.5" wide x 7.8" high) (31.75 cm wide) x 19.8 cm high)? Compared to rack installation, PowerPods for Power are a better choice. PowerPods have the advantage of having a rotating base, which can give a clean appearance to the installation carried out. The latest industry...Is it cut or uncut? Uncut

$104

NavPod PP4900 PowerPod Uncut (Usable Face = 12.5"W x 7.8"H) ( 31.75cm L x 19.8cm H)

$365

Type:	Boat layout \| Display Media
Supplier:	NavPod
Cut/Uncut:	Uncut
Edit Style:	Drawn
Usable face:	12.4"W x 7.4"H

For policyEU detailed shipping, please see our Shipping Policy and you can find our return and refund policy here.