Pre-cut NavPod RailMount for Garmin GPSMAP 723 723xsv 743 and 743xsv Boat Outfitting

RailMount Pre-Cut for Garmin GPSMAP 723, 723xsv, 743 and 743xsv

RailMount NavPods are best used to mount an autopilot control, navigation instrument or a small chartplotter on an existing base protector. Fits any 1", 1.125" or 1.25" diameter tube. A stainless steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing when you are sitting under the vehicle on a rainy day All wiring runs from the NavPod, down the center of the stainless steel arm (the available space is 0.75″ inside the narrowest part of the arm, so keep this in mind when planning your cable route; most transducer cables will not pass through the arm), and in the pedestal protection This application provides a clean and sturdy installation for the. electronic, without having to replacer protection of the base.

The rail mounts are designed for all common standard-sized instruments, as well as 7 and 9 inch chart plotters.

Structural rigidity – Gen3 improvements now include thicker gauge acrylic coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.

Waterproof Seal – All RailMount NavPods are manufactured with a double seal system providing an excellent seal. This seal provides the best protection for your marine electronics. NavPods are designed toister to the most difficult and wet offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The internal Poron Microcell polyurethane gasket is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel – We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. Tamper-resistant nickel-chrome-plated stainless steel screws provide security combined with a little style!

Commitment to quality – We stand byour commitment by offering a 10-year warranty on all new NavPods Gen3.

PRODUCT ID: 92199
SKU: NVN-92199
CSKU: CWR-92199
REWRITE: 103310-navpod-railmount-pre -cut-f-garmin-gpsmap-723-723xsv
MPN: RMX4400-15
UPC:
ASIN:
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: Pre-Cut NavPod RailMount for Garmin GPSMAP 723, 723xsv, 743 and 743xsv
NAME_EX: Pre-cut NAVPOD RAIL Mount for GARMDANS GPSMAP 723/743XSV
PTITLE: Pre-cut NavPod RailMount for Garmin GPSMAP 723, 723xsv, 743 and 743xsv
TYPE: Boat Equipment | Display Stands
SELLER: NavPod
ELECTRONICS> MARINE ELECTRONICS

Gtags:
br>
GSpecs:

Pre-cut NavPod RailMount for Garmin GPSMAP 723, 723xsv, 743 and 743xsv Product description

Pre-cut RailMount for Garmin GPSMAP 723, 723xsv, 743 and 743xsv

RailMount NavPods are best used to mount an autopilot control, navigation instrument, or small chartplotter to an existing plinth. Fits any 1", 1.125" or 1.25" diameter tube. A stainless steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing when you are sitting under the vehicle on a rainy day All wiring runs from the NavPod, down the center of the stainless steel arm (the available space is 0.75″ inside the narrowest part of the arm, so keep this in mind when planning your cable route; most transducer cables will not pass through the arm, and into the cradle protection.te application provides a clean, sturdy installation for electronics, without the replacement of the base guard.

The rail mounts are designed for all popular standard-sized instruments, as well as plotters of 7- and 9-inch boards.

Structural Rigidity – Gen3 enhancements now include thicker gauge acrylic-coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.

Waterproof Seal – All RailMount NavPods are manufactured with a double seal system providing an excellent seal. ThisSeal provides the best protection for your marine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The internal Poron Microcell polyurethane seal is now 50% thicker and is not subject to "retentive compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel – We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. Nickel-plated stainless steel tamper-proof screwschrome offer safety combined with a little style!

Commitment to quality – We stand behind our commitment by offering a 10-year warranty on all new NavPods Gen3.

Frequently asked questions (FAQ) about the NavPod RailMount Pre-Cut f/Garmin GPSMAP 723, 723xsv, 743 and 743xsv Who is the NavPod?
Who is the NavPod? Navpod is a better way to mount your fishfinder, radar or GPS. The unique waterproof seal, build quality and attractive design make the best-built instrument case ever available to the marine industry. Features of all Navpods include waterproof silicone seal, tamper-proof clips for added security and convenience, concealed wiring and clean installation for easy access.

Save $119 when you purchase the NavPod RailMount Pre-Cut f/Garmin GPSMAP 723, 723xsv, 743 and 743xsv for only $420fromNVN Marine! Same day dispatch before 3 p.m. NavPod RailMount Pre-Cut f/Garmin GPSMAP 723, 723xsv, 743 & 743xsv Technical Specifications

Type:	Boat Equipment \| Display Media
Supplier:	NavPod

Pre-Cut NavPod RailMount for Garmin GPSMAP 723, 723xsv, 743 and 743xsv User Reviews Pre-Cut NavPod RailMount for Garmin GPSMAP 723, 723xsv, 743 and 743xsv Shipping and Returns

For detailed shipping terms, please review our shipping policy and you can find our return and refund policy here.