Shaft seal PSS 2-¼" shaft 4" tube Marine Hardware
PSS Shaft Seal, 2-1/4" Shaft, 4" TubeShaft Diameter: 2-1/4 "
Stern tube Diameter (D): 4"
Total length (A): 9.625"
Total length (compressed) ) (Compressed A): 8.375 "
Rotor diameter (B): 4.2"
Carbon collar diameter (C): 3.75"
Rear Collar Length (E): 2"
PSS Shaft Seal is the marine mechanical seal best-selling worldwide and is installed as standard equipment by many of the most reputable boat builders/yards The PSS shaft seal is also recognized as the leading retrofit seal (market). secondary) in the global market Certified by
Bureau Veritas, ABS and Rina: boat builders/yards recognize the value of installing PSS as it eliminates maintenance, constant adjustment and. cost associated with traditional cable glands.These benefits, the PSS shaft seal helps eliminate water in the bilge. (100% waterproof) and wear on the propeller shaft. The PSS shaft seal
can be easily retrofitted and is available for shafts ranging from 3/4"
(20 mm) to 6" (150 mm).
The PSSshaft seal is a mechanical seal created between the flat surfaces of the rotating stainless steel rotor and the fixed carbon flange. The carbon fixed bridle is attached to the ship's stern tube with hose clamps and the carbon bridle is attached to the front of the bellows with hose clamps. The stainless steel rotor is mounted on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is attached to the shaft with set screws. This compression (preload) maintains contact between the faces and allows the
PSS to compensate for the thrust of the propeller. The carbon flange is reamed larger than the diameter ofthe shaft, which allows it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two O-rings that are recessed into the collar bore. These O-rings rotate with the stainless steel shaft and rotor and experience no wear during operation.
**As with any rubber hose below the waterline, the PSS bellows must be inspected on a regular basis for any signs of wear, aging or chemical deterioration.
PYI suggests, as preventative maintenance, that the PSS bellows be replaced every six years. When replacing the bellows, it is recommended to also replace the stainless steel rotor O-rings and adjustment screws. Sulfuric acid vapors will accelerate rubber deterioration, as will an ozonator.
Maintenance kit includes componentsitems you need to properly maintain your PSS shaft seal. Kit includes one (1) PSS. Below are two (2) O-rings, and five (5) set screws, four (4) new hose clamps and an allen wrench.
The sealless sealing system (PSS) shaft seal is a mechanical seal that can be established between a rotating stainless steel collar (rotor) and a fixed carbon flange (stator). .
PRODUCT ID: 50868
SKU: NVN-50868
CSKU: CWR-50868
REWRITE: 61979-pss-shaft-joint-2-shaft-4-tubes
MPN: 02 -214-400
UPC:
ASIN:
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: PSS Shaft Seal 2-¼" Shaft 4" Tube
EX_NAME: PSS SHAFT SEAL 2 1/4" SHAFT 4" TUBE
PTITRE: PSS Shaft Seal 2-¼" Shaft 4" Tube
TYPE: Marine Hardware | Shaft Seals
SUPPLIER: PSS Shaft Seal
SPORTING GOODS> OUTDOOR LEISURE> BOATING & WATER SPORTSES PSS (Packless Sealing System) Shaft Seal – 1-1/8" SHrear
Gtags:
GSpecs:
PSS Shaft Seal 2-¼" Shaft 4" Tube Product Description PSS Shaft Seal 2-1/4" Shaft 4" Tube
L Diameter Shaft: 2 -1/4"
Stern tube diameter (D): 4"
Overall length (A): 9.625"
Total length (compressed) (Compressed A): 8.375"
Rotor diameter (B): 4.2"
Carbon cuff diameter (C): 3.75"
Rear cuff length (E): 2"
The seal PSS Shaft Sealis the best-selling marine mechanical seal worldwide and is fitted as standard equipment by many of the world's leading boat builders/yards. The PSS Shaft Seal is also recognized. as the first retrofit seal (aftermarket) certified by Bureau Veritas, ABS & Rina: Boat builders/yards recognize the benefits and value of installing PSS as it eliminates maintenance, constant adjustment. and the cost associated with the cable glands ttraditional. PSS Shaft Sealhelps eliminate water in the bilge (100% waterproof) and wear on the propeller shaft. The PSS shaft seal
can be easily retrofitted and is available for shafts ranging from 3/4"
(20 mm) to 6" (150 mm).
The PSSshaft seal is a mechanical seal created between the flat surfaces of the rotating stainless steel rotor and the fixed carbon flange. The carbon fixed bridle is attached to the ship's stern tube with hose clamps and the carbon bridle is attached to the front of the bellows with hose clamps. The stainless steel rotor is mounted on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is attached to the shaft with set screws. This compression (preload) maintains contact between the faces and allows the
PSS to compensate for the thrust of the propeller. The carbon flange is reamed larger than the diameter of the arbre, which allows it to "float" around the shaft and thus compensates for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two O-rings which are recessed into the collar bore. These O-rings rotate with the stainless steel shaft and rotor and experience no wear during operation.
**As with any rubber hose below the waterline, the PSS bellows must be inspected on a regular basis for any signs of wear, aging or chemical deterioration.
PYI suggests, as preventative maintenance, that the PSS bellows be replaced every six years. When replacing the bellows, it is recommended to also replace the stainless steel rotor O-rings and adjustment screws. Sulfuric acid vapors will accelerate the deterioration of rubber, as will an ozonator.
The maintenance kit includes the items yous need to properly maintain your
PSS Shaft Seal Inc. Kit includes one (1) PSS boot, two (2) O-rings, five (5) set screws, four (4) new hose clamps and one Allen key.
The sealless seal system (PSS) shaft seal is a mechanical seal that can be established between a rotating stainless steel collar (rotor) and a fixed carbon flange (stator)...
PSS Shaft Seal, 2-¼" Shaft, 4" Tube Related ProductsPSS Shaft Seal Service Kit, 2 1/4" Shaft, 4" Tube
Frequently Asked Questions (FAQ) about PSS Shaft Seal 2-¼" Shaft 4" Tube Who is PSS Shaft Seal?
How to describe the seal PSS shaft seal 2-¼" Shaft 4" Tube?
Who is the PSS shaft seal? The PSS Shaft Seal is the world's best-selling marine mechanical seal and is installed as standard equipment by many of the world's leading shipyards and boat builders.The PSS Shaft Seal is also recognized as the leading retrofit (aftermarket) seal in the global market.describe PSS Shaft Seal, 2-¼" Shaft, 4" Tube ? The sealless seal system (PSS) shaft seal is a mechanical seal that can be established between a rotating stainless steel collar (rotor) and a fixed carbon flange (stator)...
Save $167 when you buy the PSS Shaft Seal 2-¼" Shaft 4" Tube for only $669 at NVN Marine ! Free same day delivery before 3 p.m. PSS Shaft Seal 2-¼" Shaft 4" Tube Videos PSS Shaft Seal 2-¼" Shaft 4" Tube Technical Specifications
| Type: | Marine Equipment | Shaft Seals |
|---|---|
| Supplier: | PSS Shaft Seal |
| Product brochure: | Download PDF |
| Product installation: | Download PDF |
For detailed shipping policy, please see our Shipping Policy and you can find our Return & Refund Policy here.
/p>
