Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC Electrical
BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it no longer has enough power left to crank the engine. Battery Protect is a unidirectional device. It can only handle current in one direction, so either current to a load or current coming from a charger, but not both currents at the same time. Additionally, current can only flow from the battery terminal to the charging terminal. When used with a load, the battery connects to the Battery terminal, and when used with a charger, the charger connects to the Battery terminal.BatteryProtect BP-100 - 100AMP - 6-35 VDC
Features:
- The BatteryProtect disconnects the battery from non-essential loads before completely discharged (which will damage the battery) orbefore there is no longer enough power left to crank the engine.
- 12/24V Auto Range The BatteryProtect automatically senses system voltage
- Simplified Programming The BatteryProtect can be configured to turn on/off at several different voltages. The seven segment display will indicate which setting has been chosen.
- A special setting for Li-ion batteries. In this mode, the BatteryProtect can be controlled by the VE.Bus BMS. Note: The BatteryProtect can also be used as a load switch between a battery charger and a Li-ion battery. See connection diagram in the manual.
- Ultra low current consumption This is important in the case of Li-ion batteries, especially after a low voltage shutdown. Please see our Li-ion battery datasheet and VE.Bus BMS manual for more information.
- Overvoltage protection To avoid endommager sensitive loads due to overvoltage, the load is disconnected whenever the DC voltage exceeds 16 V respectively 32 V.
- Ignition proof No relays but MOSFET switches, and therefore no sparking.
- Delayed Alarm Output The alarm output is activated if the battery voltage drops below the preset disconnect level for more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit resistant open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnection and delayed reconnection The load will be disconnected 90 seconds after the alarm is activated. If the battery voltage increases again to the connection threshold during this period (after starting the engine for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage increases beyond the preset reconnection voltage.
Warranty Information
This product can expose you to chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. For more information, go to P65Warnings.ca.gov.
Please contact your dealer for any returns, repairs or problems. support related to this product.BatteryProtect 12/24V- 100A-BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it there is enough power to start the engine. The battery protector is a one-way device. It cannot handle.current only in one direction, so it can handle both the load current and the charger current, but it cannot handle two currents at the same time. Additionally, current can only flow from the battery terminal to the charging terminal. If a charge is used, the battery is connected to the battery terminal, and if a charger is used, the charger is connected to the battery terminal.
PRODUCT ID: 82907
SKU: NVN-82907
CSKU: CWR-82907
REWRITE: 94018-victron-batteryprotect-bp-100-100amp-6-35
MPN: BPR000100400
br> UPC: 8719076021438
ASIN: B01KIF2BGW
WSKU:
SSKU: VIC-BPR000100400
KSKU: VICBPR0001004
GSKU: BPR000100400
MSKU:
LSKU:
NAME : Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC
NAME_EX: VICTRON BATTERYPROTECT 12/24V-100A
PTITLE: Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC
TYPE: Electric | Battery management
SUPPLIER: Victron Energy
VEHICLES & PARTS> VEHICLE PARTS & ACCESSORIES> POWERWATER PARTS & ACCESSORIES
CE
Victron BatteryProtect BP-100-100AMP - 6 -35 VDC
Google Title : Victron Battery Protect 12/24V 65A 100A & 220A - BP-100A
CE
Gtags:
| Victron Energy |
Specifications G:
Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC Product Description The BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has any remaining enough power to crank the engine. Battery Protect is a unidirectional device. It can only handle current in one direction, so either current to a load or current coming from a charger, but not both currents at the same time. Additionally, current can only flow from the battery terminal to the charging terminal. When used with a load, the battery connects to the Battery terminal, and when used with a charger, the charger connects to the Battery terminal.
BatteryProtect BP-100 - 100AMP - 6-35 VDC
Features:
- The BatteryProtect disconnects the battery from non-essential charges withbefore it is completely discharged (which would damage the battery) or before it is insufficientThere is no more power left to start the engine.
- 12/24V Auto Range The BatteryProtect automatically senses the system voltage
- Simplified Programming The BatteryProtect can be configured to turn on/off at several different voltages. The seven segment display will indicate which setting has been chosen.
- A special setting for Li-ion batteries. In this mode, the BatteryProtect can be controlled by the VE.Bus BMS. Note: The BatteryProtect can also be used as a load switch between a battery charger and a Li-ion battery. See connection diagram in the manual.
- Ultra low current consumption This is important in the case of Li-ion batteries, especially after a low voltage shutdown. Please see our Li-ion battery datasheet and VE.Bus BMS manual for moreinformation.
- Overvoltage protection To avoid damage to sensitive loads due to overvoltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V.
- Proof of ignition No relay but MOS FET switches, and therefore no sparking.
- Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnection level for more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit resistant open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnection and delayed reconnection The load will be disconnected 90 seconds after the alarm is activated. If the battery voltage increases again to the connection threshold during this period (after thestarting the engine for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage increases beyond the preset reconnection voltage.
Warranty Information
WARNING:This product can expose you to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information,
Please contact your dealer for any returns, repairs, or support issues related to this product.BatteryProtect 12/24V- 100A-BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which will damage the battery) or before there is sufficient power to start the engine. The battery protector is a one-way device. He can't handle the heartonly in one direction, it can therefore manage both the load current and that of the charger, but it cannot manage two currents at the same time. Additionally, current can only flow from the battery terminal to the charging terminal. If a charge is used, the battery is connected to the battery terminal, and if a charger is used, the charger is connected to the battery terminal.
Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC Related productsAncor black battery cable 4 AWG - 25'
Ancor red battery cable 4 AWG - 25'
Cable Ancor yellow battery cable 4 AWG - 25'
Ancor black battery cable 2 AWG - 25'
Ancor red battery cable 2 AWG - 25'
Ancor yellow battery cable 2 AWG - 25 '
Ancor Heavy Duty Lugs - 2 Gauge Wire - 5/16" Post - Pack of 2
Ancor Heavy Duty Lugs - 2 Gauge Wire - 5/16" Post - 25 Pack
Lugs Ancor Heavy Duty - 1 Gauge Wire - 5/16" Post - Packand 2
Ancor Heavy Duty Terminals - 1 Gauge Wire - 5/16" Post - Pack of 25
Frequently Asked Questions (FAQ) about Victron BatteryProtect BP- 100 - 100AMP - 6-35 VDC Who is Victron Energy?
How to describe Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC?
What are the dimensions and weight of the Victron BatteryProtect BP-100 package - 100AMP - 6-35 VDC?
What are the manufacturer's ratings for Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC?
Who is Victron Energy Victron Energy? is a global company renowned for its technical innovation, reliability and build quality. Victron products, which excel in the efficient combination of two or more separate energy sources, are recognized internationally as the professional choice for power systems. resilient energy storage Victron products include sine wave inverters, sine wave inverters/chargers,battery chargers, DC/DC converters, transfer switches, battery monitors and much more. How to describe Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC? BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it no longer has enough power left to crank the engine. Battery Protect is a unidirectional device. It can only handle current in one direction, so either current to a load or current coming from a charger, but not both currents at the same time. Additionally, current can only flow from the battery terminal to the charging terminal. When used with a load, the battery connector connects to the battery terminal, and when used with a charger, the charger connects to the battery terminal.What are the dimensions and weighte packaging Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC? 3 (w) X 3 (h) VDC? BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it no longer has enough power left to crank the engine. Battery Protect is a unidirectional device. It can only handle current in one direction, so either current to a load or current coming from a charger, but not both currents at the same time. Additionally, current can only flow from the battery terminal to the charging terminal. When used with a load, the battery connects to the Battery terminal, and when used with a charger, the charger connects to the B terminal.
Econobid $9 when you buy the Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC for only $53 from NVN Marine! Same day dispatch before 3 p.m. Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC Videos Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC Technical specifications
| Type: | Electric | Battery management |
|---|---|
| Supplier: | Victron Energy |
| Weight: | 1.1 lbs |
| User Guide: | Download PDF |
| Product installation: | Download PDF |
| Shipping Weight: | 1.1 lbs |
|---|---|
| Box Sizes: | 3.00 (h) x 3.00 (w) x 8,00 (l) |
| Cubic feet: | 72.0 |
| P65: | Yes |
For detailed shipping terms, please review our shipping policy and you can find our return and refund policy here.
