Victron MultiPlus 12/3000 - 120-50 - 230V - VE.Bus Electrical

MultiPlus 12/3000 - 120-50 - 230V - VE.Bus

The MultiPlus, as its name suggests, is an inverter and charger combined in one only elegant case. Its many features include a true sine wave inverter, adaptive charging, PowerAssist hybrid technology and several system integration features.

Two AC outputs

The main output has uninterrupted functionality. The MultiPlus supports powering connected loads in the event of a grid outage or when shore/generator power is disconnected. This happens so quickly (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without interruption.

The second output is active only when alternating current is available on the MultiPlus input. Loads that should not discharge the battery, such as a water heater for example, canmust be connected to this output (a second output is available on models rated at 3 kVA and above).

Virtually unlimited power through parallel operation

Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will provide an output power of 25 kW/30 kVA with a load capacity of 720 AMP.

Three phase capacity

In addition to parallel connections, three units of the same model can be configured for three-phase output. But that's not all: up to 6 sets of three units can be connected in parallel for a 75 kW/90 kVA inverter and a load capacity of over 2000 A.

PowerControl - Manage limited generator, dock. Side or network power

The MultiPlus is a very powerful battery charger. It will therefore consume a lot of current from the generator or theshore power (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel, a maximum generator or shore current can be set. The MultiPlus will then take into account other AC loads and use whatever is extra for charging, preventing generator or short circuits. The power supply is not overloaded.

PowerAssist - Increase the capacity of shore power or generator

This feature takes the principle of PowerControl to an additional dimension. It allows MultiPlus to supplement the capacity of the alternative source. Where peak power is often only required for a limited period, the MultiPlus will ensure that insufficient power from the dock or generator is immediately compensated by battery power. When the load reduces, the available energy is used to recharge the battery.

Solar energy: powerAC is available even in the event of a grid outage

The MultiPlus can be used in photovoltaic and other off-grid as well as grid-connected alternative energy systems. Power loss detection software is available.

System configuration:

In the case of a standalone application, if any Parameters need to be changed, this can be done in minutes with a DIP switch setting procedure
Parallel and three-phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator
Off-grid, grid-interactive and self-consumption applications, involving grid-connected inverters and/or MPPT solar chargers can be configured with wizards (software dedicated to specific applications)

On-site monitoring and control

Several options areavailable: Battery monitor, multiple control panel, color control for GX or other GX devices, smartphone, tablet (Bluetooth Smart), laptop or computer (USB or RS232).

Monitoring and remote control Color Control GX or other GX devices. Data can be stored and displayed for free on our VRM (Victron Remote Management) website.

Remote configuration

When connected to Ethernet , systems with a Color Control GX or other GX device can be accessed and settings can be changed remotely

Specifications:

PowerControl : Yes
PowerAssist: Yes
Transfer switch (A): 16 or 50

Inverter specifications:

Input voltage range (V DC): 9.5 – 17 V 19 – 33 V 38 – 66 V
Output: Output voltage : 230 VAC, ± 2% / Frequency 50 Hz± 0.1%(1)
Continuous output power at 25°C (VA): 3000
Continuous output power at 25°C (W): 2400
Continuous output power at 40°C (W): 2200
Continuous output power at 65°C (W): 1700
Peak power ( W ): 6000
Maximum efficiency (%): 93 / 94 / 95
No load power (W): 20 / 20 / 25
No load Power in AES mode (W): 15/15/20
Power at zero load in search mode (W): 8/10/12

Charger Specifications:

AC Input: Input Voltage Range: 187-265 VAC / Input Frequency: 45-65 Hz / Power Factor: 1
Absorption charging voltage (V DC): 14.4 / 28.8 / 57.6
Float charging voltage (V DC): 13.8 / 27.6 / 55 .2
Storage Mode (V DC): 13.2 / 26.4 / 52.8
Domestic battery charging current (A): 120 / 70 / 35
li>
Starting battery charging current (A): 4 (12V and 24V models onlyuement)
Battery temperature sensor: Yes

General specifications:

Auxiliary output : Yes (16A)
Programmable relay: Yes
Protection: a - g
VE.Bus communication port: For parallel and three-phase operation, monitoring distance and systems integration
General purpose Com. Port: Yes
Remote On/Off: Yes
Common Features: Temp. range: -40 to +65°C (fan-assisted cooling) / Humidity (non-condensing): max 95%

Case specifications:

Common features: Material and color: aluminum (blue RAL 5012) / Protection category: IP 21
Battery connection: Four M8 bolts (2 plus connections and 2 minus connections )
230V AC connection: 13mm^2 (6 AWG) screw terminals M6 bolts
Weight (kg): 18
Dimensions (hxwxd in mm): 362 x 258 x 218

Standards

Safety: EN-IEC 60335-1, EN-IEC 60335-2-29, IEC 62109-1
Emission, immunity: EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2 , IEC 61000-6-3
Road vehicles: 12V and 24V models: ECE R10-4
Anti-Islanding: See Victron website
Can be set to 60 HZ. 120 V models available on request
Protection key: output short circuit, overload, battery voltage too high, battery voltage too low, temperature too high, 230 VAC on inverter output, ripple input voltage too high
Non-linear charging, 3:1 crest factor
Up to 25°C ambient
Turns off when 'no external AC source is available
Programmable relay which can, among other things, be set for a general alarm, including a DC undervoltage or generator start/stop function / Current alternative: 230 V/4 A / Continuous current: 4 A up to 35 V DC, 1 A up to 60 V DC / A.o. communicate with a lithium-ion battery BMS

Please contact your dealer for any return, repair or support issues related to this product.

Please contact your dealer for any return, repair, or support issues related to this product.

PRODUCT ID: 86166
SKU: NVN-86166
CSKU: CWR-86166
REWRITE: 97277-victron-multiplus-12-3000-120-50-230v
MPN: PMP123021010
UPC: 8719076023951
ASIN:
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: VICTRON MULTIPLUS 12/3000/120 -50 230 V VE.BUS
NAME_EX:
PTITLE: Victron MultiPlus 12/3000 - 120-50 - 230V - VE.Bus
TYPE: Electric | Charger/Inverter Combos
SELLER: Victron Energy
ELECTRONICS> ELECTRONIC ACCESSORIES> POWER

Gtags:

GSpecs:

Victron MultiPlus 12/3000 - 120-50 - 230V - VE.Bus Product description

MultiPlus 12/3000 - 120-50 - 230V - VE.Bus

The MultiPlus, as the name suggests, is a combined inverter and charger in one sleek package. Its many features include a true sine wave inverter, adaptive charging, PowerAssist hybrid technology and several system integration features.

Two AC outputs

The second output is active only when alternating current is available on the MultiPlus input. The charges whichmust not drain the battery, such as a water heater for example, can be connected to this output (a second output is available on models rated at 3 kVA and above).

Power virtually unlimited thanks to parallel operation

Up to 6 Multis can operate in parallel to achieve higher output power. Six 24/5000/120 units, for example, will provide an output power of 25 kW/30 kVA with a load capacity of 720 AMP.

Three phase capacity

PowerControl - Manage limited generator, dock. Side or network power supply

The MultiPlus is a battery chargervery powerful. It will therefore draw a lot of current from the generator or shore power (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel, a maximum generator or shore current can be set. The MultiPlus will then take into account other AC loads and anything extra for charging, preventing overloading of the generator or shore power.

PowerAssist - Increase the capacity of shore power or generator

This feature takes the principle of PowerControl to an additional dimension. It allows MultiPlus to supplement the capacity of the alternative source. Where peak power is often only required for a limited period, the MultiPlus will ensure that insufficient power from the dock or generator is immediately compensated by battery power. When the charge reduces, the available energy is used to rechargethe battery.

Solar power: AC power is available even in the event of a grid outage

The MultiPlus can be used in photovoltaic systems and other off-grid as well as grid-connected alternative energy systems. Power loss detection software is available.

System configuration:

In the case of a standalone application, if any parameters need to be changed, this can be done in a few minutes with a DIP switch setting procedure
Parallel and three-phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software
Off-grid, on-grid -Interactive and self-consumption applications, involving grid-connected inverters and/or MPPT solar chargers, can be configured with wizards (dedicated software for specific applications)

SurvOn-site monitoring and control

Several options are available: battery monitor, multiple control panel, color control for GX or other GX devices, smartphone, tablet (Bluetooth Smart), laptop or computer (USB or RS232).

Remote monitoring and control

Color Control GX or other GX devices. Data can be stored and displayed for free on our VRM (Victron Remote Management) website.

Remote configuration

When connected to Ethernet , systems with a Color Control GX or other GX device can be accessed, and settings can be changed remotely

Specifications:

PowerControl : Yes
PowerAssist: Yes
Transfer switch (A): 16 or 50

Inverter specifications:

Input voltage range (V DC): 9.5 – 17 V 19 – 33 V 38 – 66 V
Output: Output voltage: 230 VAC, ± 2% / Frequency 50 Hz ± 0.1%(1)
Continuous Output power at 25°C (VA): 3,000
Continuous output power at 25°C (W): 2400
Continuous output power at 40°C (W): 2200
Output power continuous at 65°C (W): 1700
Maximum power (W): 6000
Maximum efficiency (%): 93 / 94 / 95
Power at no load (W): 20 / 20 / 25
Power at no load in AES mode (W): 15 / 15 / 20
No load Power in search mode ( W): 8/10/12

Charger Specifications:

AC Input: Input Voltage Range: 187-265 VAC / Input frequency: 45 – 65 Hz / Power factor: 1
Load voltage absorption (V DC): 14.4 / 28.8 / 57.6
Float charge voltage (V DC): 13.8 / 27.6 / 55.2
Storage mode (V DC): 13.2 / 26.4 / 52, 8
House battery charging current (A): 120/70/35
Starting battery charging current (A): 4 (12V and 24V models only)
Battery temperature sensor: Yes

General specifications:

Auxiliary output: Yes (16 A)
Programmable relay: Yes
Protection: a - g
VE.Bus communication port: For parallel and three-phase operation, remote monitoring and system integration
General purpose com. Port: Yes
Remote On/Off: Yes
Common Features: Temp. range: -40 to +65°C (fan-assisted cooling) / Humidity (non-condensing): max 95%

Case specifications:

Common features: Material and color: aluminum (blue RAL 5012) / Protection category: IP 21
Battery connection: Four M8 bolts (2 plus connections and 2 minus connections )
230 V ACn connection: Screw terminals 13 mm ^ 2 (6 AWG) M6 Bolts
Weight (kg): 18
Dimensions (hxwxd in mm): 362 x 258 x 218

Standards

Safety: EN-IEC 60335-1, EN-IEC 60335-2-29, IEC 62109-1
Emission, immunity: EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6 -3
Road vehicles: 12V and 24V models: ECE R10-4
Anti-islanding: see Victron website
Can be adjusted to 60 Hz. 120 V models available on request
Protection key: output short circuit, overload, battery voltage too high, battery voltage too low, temperature too high, 230 VAC on inverter output , input voltage ripple too high
Non-linear load, crest factor 3:1
Up to 25°C ambient
S' off when no external AC source is available
Programmable relay which can, among other things, be set for a general alarm, includings a DC undervoltage or generator set start/stop function / AC rating: 230V/4A / DC rating: 4A up to 35VDC, 1A up to 60VDC / A.o. to communicate with a lithium-ion battery BMS

Please contact your dealer for any returns, repairs, or support issues related to this product.

Please contact your dealer for any returns, repairs, or support issues related to this product.

Save $250 when you purchase the Victron MultiPlus 12/3000 - 120-50 - 230V - VE.Bus for only $1,419 from NVN Marine! Free same day delivery before 3 p.m. Victron MultiPlus 12/3000 - 120-50 - 230V - VE.Bus Videos Victron MultiPlus 12/3000 - 120-50 - 230V - VE.Bus Technical specifications

Type:	Electric \| Charger/Inverter Combos
Supplier:	Victron Energy
Weight:	47.4 lbs
ProManual conduit:	Download PDF

Victron MultiPlus 12/3000 - 120-50 - 230V - VE.Bus Opinions of usersVictron MultiPlus 12/3000 - 120-50 - 230V - VE.Bus Shipping and Returns

Shipping Weight:	47.4 lbs
Box sizes:	13.00 (h) x 14.00 (w) x 18.00 (l)
Cubic feet:	3276.0