BEP Pro Installer 400a EZ Mount Dual Bank Control Battery Switch - MC10 Electrical

Pro Installer 400A EZ-Mount Dual Bank Control Battery Switch - MC10

Another addition to our multi-award-winning Pro Installer EZ Mount line, the innovative Control Switch Dual bank is like 3 switches in one, Home, Start and Emergency Parallel. Providing intuitive, easy control for the boater, the dual-bank control switch features a unique isolated position that allows use of household loads and the VHF radio if the engine needs to be electrically isolated, or allows for isolation of the engine during maintenance while providing electricity to power loads (for lights, stereo, refrigerator, etc.). For boats or vehicles equipped with a single engine and house battery bank, Dual Bank Control allows the use of battery banks optimized for their respective loads; a properly sized deep cycle battery for the loads domestics and thin plate starting batteries for the engine. Additionally, sensitive electronics are isolated from starter-induced voltage spikes because the house and engine loads are separated during normal starting operation, unlike Selector battery disconnect switches. As simple as 1, 2, 3, these revolutionary EZ Mount battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnect height, EZ-Mount Battery Switches "gang" directly with the Pro Installer busbar line, resulting in the fastest, most compact installations. Optimized cable access makes installation easy.

Tested to UL1107, CE ignition protection
10 tinned copper studs mm (3/8 inch)
Stainless steel washers and nuts
Reinforced plasticsfiber cables
400 A continuous / 600 A 5 minutes intermittent / 1500 A 10 seconds Start (cable size to achieve 120 mm ratings}, 4/0, one smaller cable size will reduce current rating)
Waterproof IP67
Same interconnect height as Pro Installer
Removable button allows for isolation during servicing
3 removable side plates for protection
Industry standard 3.85 x 3.85 inch footprint
For surface mounting only
Each Pro Installer battery switch is fully tested for pressure tightness, rotational force and electrical load

Specifications
Mounting: Surface only
Voltage: 48V DC (for 12-48V systems, both banks must have the same voltage)
Rating: 400 Cont / 600 Inter / 1500 Crank
Dims: 3.85" x 3.85" x 3.62"
Operation: 1, 1/2, parallel, disabled
Stud: 4x 10 mm (3.8")

This product can expose you to chemicals including di(2-ethylhexyl) phthalate (dehp), which is known to the State of California to cause cancer, birth defects or other reproductive problems. For more information,

These revolutionary battery disconnect switches allow you to wire from the front. Installation and wiring are simple and easy. With its shared interconnect height, ez-mount...
PRODUCT ID: 58594
SKU: NVN-58594
CSKU: CWR-58594
REWRITE: 69705-bep-pro-installer- 400a-ez-mount-dual-bank
MPN: 772-DBC-EZ
UPC: 843687008583
ASIN: B01L5DPJ24
WSKU:
SSKU:
KSKU:
GSKU :
MSKU:
LSKU: 69-772DBCEZ
NAME: BEP Pro Installer 400a Battery SwitchEZ-Mount Dual Bank Control Battery Switch - MC10
EX_NAME: BEP PRO INSTALLER 400A EZMOUNT DOUBLE BANK COTNROL SWITCH
PTITLE: BEP Pro Installer 400a EZ-Mount Dual Bank Control Battery Switch - MC10
br> TYPE: Electric | Battery Management
SELLER: BEP Marine
VEHICLES & PARTS> VEHICLE PARTS & ACCESSORIES> WATERCRAFT PARTS & ACCESSORIES
Sports
BEP MC10 Pro Installer 400A EZ-Mount Dual Bank Control Battery Switch
Bep Pro Installer 400a EzMount Dual Bank ControlMc1 Battery Switch by Hodges Marine
Sports
Gtags:

Switch
Safety switch

GSpecs:

BEP Pro Installer 400a EZ-Mount Dual Bank Control Battery Switch - MC10 Product Description Pro Installer 400A EZ-Mount Dual Bank Control Battery Switch - MC10

Another addition to our award-winning Pro Repeatedly Range Install EZ Mount, the innovative dual bank control switch is like 3 switches in one, home, start and parallel emergency. Providing intuitive, easy control for the boater, the dual-bank control switch features a unique isolated position that allows use of household loads and the VHF radio if the engine needs to be electrically isolated, or allows for isolation of the engine during maintenance while providing electricity to power loads (for lights, stereo, refrigerator, etc.). For boats or vehicles equipped with a single engine and house battery bank, Dual Bank Control allows the use of battery banks optimized for their respective loads; Ae suitably sized deep cycle battery for household loads and thin plate starting batteries for the engine. Additionally, sensitive electronics are isolated from starter-induced voltage spikes because the house and engine loads are separated during normal operation, unlike the shifter battery switches. As simple as 1, 2, 3, these revolutionary EZ Mount battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnect height, EZ-Mount Battery Switches "gang" directly with the Pro Installer busbar line, resulting in the fastest, most compact installations. Optimized cable access makes installation easy.

Tested to UL1107, CE ignition protection
10 tinned copper studs mm (3/8 inch)
Stainless steel washers and nuts
Fiber reinforced plastics
400 A continuous / 600 A 5 minutes intermittent / 1500A 10 seconds Start (cable size to achieve 120mm ratings}, 4/0, smaller cable size will reduce current rating)
Waterproof IP67
Same interconnection height as Pro Installer
Removable button allows isolation during maintenance
3 removable side plates for protection
Industry standard footprint of 3.85 x 3.85 inches
For surface mount only
Each Pro Installer battery switch is fully tested for pressure tightness, rotational force and electrical load

This product can expose you to chemicals including the state recognized di(2-ethylhexyl) phthalate (dehp). of California to cause cancer, birth defects, or other reproductive harm. For more information,

These revolutionary battery disconnect switches allow you to wire from the front. Installation and wiring are simple and easy. With its shared interconnect height, ez-mount...

BEP Pro 400a Installer EZ-Mount Dual Bank Control Battery Switch - MC10 Related ProductsAncor Black Battery Cable 2 AWG - 25'
Ancor Red 2 AWG Battery Cable - 25'
Ancor Black 2/0 AWG Battery Cable - 100'
Ancor Red 2/0 AWG Battery Cable - 100'
CossAncor Heavy Duty Terminals - 2 Gauge Wire - 3/8" Post - Pack of 2
Ancor Heavy Duty Terminals - 2 Gauge Wire - 3/8" Post - 25 Pack
Ancor Heavy Duty Terminals - Wire 1 Gauge - 3/8" Post - Pack of 2
Ancor Heavy Duty Lugs - 1 Gauge Wire - 3/8" Post - Pack of 25
Ancor Heavy Duty Lugs - 1 Gauge Wire 0 - 3/8" Post - Pack of 2
Ancor Heavy Service Lugs - 1/0 Gauge Wire - 3/8" Post - Pack of 25

BEP Pro Installer Frequently Asked Questions (FAQ) EZ-Mount 400a Double Row Control Battery Switch - MC10 Who is BEP Marine?
How to Describe BEP Pro Installer 400A EZ-Mount Dual Row Control Battery Switch - MC10?
What position ions exist in this product?
Latching product?
Does this switch have an option to disconnect the alternator field?
Who is BEP Marine? BEP designs and manufacturesue a range of high quality electrical solutions designed for harsh marine and motorhome environments. Each product manufactured meets rigorous performance specifications and is designed to withstand conditions at sea and on land. BEP engineers and product managers continue to develop the next generation of energy management products. How to describe the BEP Pro Installer 400a EZ Mount Dual Bank Control Battery Switch - MC10? These revolutionary battery disconnects allow you to wire from the front. Installation and wiring are simple and easy. With its shared interconnect height, ez-mount...What positions exist in this product? 1-1/2-Parallel-OffLockable product? No, does this switch have an option to disconnect the alternator field? No

Save $42 when you purchase the BEP Pro Ins Control Battery SwitchDual Bank EZ-Mount 400a Larger - MC10for only $65 from NVN Marine! Same day dispatch before 3 p.m. BEP Pro Installer 400a EZ Mount Dual Bank Control Battery Switch - MC10 Technical Specifications

Type:	Electric \| Battery management
Supplier:	BEP Marine
Weight:	1.4 lbs
AFD:	No
Lockable:	No
Positions:	1-1/2-Parallel-Off
Continuous intensity:	400a
User Guide:	Download PDF
Product Manual:	Download PDF
Product Installation:	Download PDF

BEP Pro Installer 400a Battery SwitchEZ-Mount Dual Control Battery Switch - MC10 User ReviewsBEP Pro EZ-Mount Installer 400a Dual Row Control Battery Switch - MC10 Shipping & Returns

Shipping Weight:	1.4 lbs
Box sizes:	3.00 (h) x 7.00 (l) x 8.00 (l)
Cubic feet:	168.0
Returnable:	Yes
P65:	Yes