Maretron Submersible Pressure Transducer - 0 to 3 PSI Marine Navigation & Instruments

Maretron Fluid Pressure Sensor Transducers work with the Maretron FPM100 which will adapt up to six pressure transducers to the NMEA 2000 network. Submersible Pressure Transducer - 0 to 3 PSI Used for tanks up to 80" or 2 M depth. When used with Maretron displays, alerts can be set so the user can be informed of low or high tank levels and when not on board. Users can be notified by email or SMS of their tank levels. Additionally, tank levels can be stored using the Maretron Data Logger (VDR100) for later analysis.

Maretron pressure transducers are not approved for use with gasoline. If you wish to use the FPM100 to monitor gasoline pressures or levels, you must obtain a pressure transducer approved for gasoline.use with gasoline.

Maretron PTS03PSI01 Attributes
Submersible pressure transducer - 0 to 3 PSI

Used for tanks up to 80" or 2M deep

SubmersiFlexible pressure transducers are used with the fluid pressure monitor from Maretron (FPM100), which allows the tank liquid level to be broadcast over a NMEA 2000 network where it can be monitored from any compatible NMEA 2000 display. When used with Maretron displays, alerts can be set so the user can be informed of low or high tank levels And when not on board the vessel, users can be informed by email or SMS of the level of their tanks. Additionally, tank levels can be stored using the Maretron Data Logger (VDR100) for later analysis.

This product can expose you to chemicals including NICKEL (METALLIC), which is known to the State of California to cause cancer. For more information, see P65Warnings.ca.gov.

Used for storage tanks with a depth not exceeding 80 inches or 2 M. The submersible pressure sensor is used with the Maretron fluid pressure monitor (FPM100) to increase tank fluid level to...

EleTechnique:

Sensor type: gauge (vent tube)
Output: 4 – 20 mA current loop, loop powered
Excitation voltage: 9 VDC to 32 VDC
Compatible Fluids/Gas: Engine Oil, Diesel, Hydraulic Fluid, Water, Waste Water
Operating Temperature: 14°F to 158°C °F (-10°C to 70°C)
Ambient temperature: 14°F to 158°F (-10°C to 70°C)
Accuracy: ±0.3% typ. full scale. at 25°C
Total error band (TEB): ±1.0% typ. (-10°C to 70°C)
Non-linearity, hysteresis (NLH): ±0.2% typ. Best Straight Line (BSL) at 25°C
Zero point and temperature compensation range: 0.04% of full scale/°F (0.02% of full scale/°C)
Long-term stability: 0.2% typ. full scale. 1 year at 25°C
Rise time: 1 ms typ. (Rated pressure from 10% to 90%)
Start-up delay: 100 ms
Overpressure: 15 PSI (1.03 bar)
Pressure Burst: 30 PSI (2.07 bar)
Vibration: 6 g (25 to 2000 Hz)
Shock: 50 g / 8 ms
Construction: AISI316L stainless steel housing, pressure fitting; Ceramic, Al2O3 sensor (96%); FKM (FPM, Viton), EPDM (TPE) seals; PUR cable
Minimum cable bending radius: 1.57â€ (40 mm)
EMC compatibility: EN/IEC 61000-6-3 / GL 2012, IV, Part 7 (emission and immunity)
Weight: 12.6 oz (357 g)

PRODUCT ID: 59814
SKU: NVN-59814
CSKU : CWR-59814
REWRITE : 70925-maretron-submersible-pressure-transducer-0-to
MPN: PTS-0-3.0PSI-01
UPC: 873804003702
ASIN: B01BTHZBLK
WSKU:
SSKU: MRTN -PTS-0-3PSI-01
KSKU: MRTPTS03PSI01
GSKU: PTS-0-3-0PSI-01
MSKU:
LSKU:
NAME: Maretron submersible pressure transducer - 0 to 3 PSI
NAME_EX: MARETRON SUBMERSIBLE PRESSURE TRANSDUCER 0 TO 3 PSI
PTITLE: Maretron Submersible Pressure Transducer - 0 to 3 PSI
TYPE: Navigation & Marine Instruments | NMEA Cables and Sensors
SELLER: Maretron
ELECTRONICS> MARINE ELECTRONICS> MARINE BOARDS & GPS
CE
AmazonTitle: Maretron PTS-0-3PSI-01 Submersible Pressure Transducer
br> Maretron Submersible Pressure Transducer - 0 to 3 PSI
CE
Gtags:

GSpecs:

Maretron Submersible Pressure Transducer - 0 to 3 PSI Product Description

Maretron Fluid Pressure Sensor Transducers work with the Maretron FPM100 which will adapt up to six pressure transducers to the NMEA 2000 network. Submersible Pressure Transducer - 0 to 3 PSI Used for tanks up to 80" or 2 M deep. When used with Maretron displays, Alerts can be configured so the user can be notified of low or high tank levels. And when not on board the vessel, users can be notified by email or SMS of their tank levels. Additionally, tank levels can be stored using Maretron data logger (VDR100) for later analysis.

Maretron pressure transducers are not approved for use with pressure transducers. gasoline If you want to use it.To use the FPM100 to monitor fuel pressures or levels, you must obtain an approved pressure transducer. for use with gasoline.

Maretron PTS03PSI01 Attributes
Transducer submersible pressure - 0 to 3 PSI

Used for tanks up to 80" or 2M deep

Submersible pressure transducers are used with Maretron's Fluid Pressure Monitor (FPM100), which allows the tank fluid level to be broadcast over a NMEA 2000 network where it can be monitored from any compatible NMEA 2000 display when it is used With Maretron displays, alerts can be set so the user can be informed of low or high tank levels. And when not on board the vessel, users can be informed by email or. by SMS of the levels of their tanks be stored using the records.Maretron data controller (VDR100) for further analysis.

This product can expose you to chemicals including NICKEL (METALLIC), which is known to the State of California to cause cancer. More information,

Used for storage tanks with depths not exceeding 80 inches or 2M. The submersible pressure sensor is used with the Maretron Fluid Pressure Monitor (FPM100) to increase the tank fluid level to...

Electrical:

Sensor type: Gauge (vent tube)
Output: 4 – 20 mA current loop, loop powered
Voltage Excitation: 9 VDC to 32 VDC
Compatible fluids/gases: engine oil, diesel, hydraulic fluid, water, waste water
Operating temperature: 14°F to 158 °F (-10°C to 70°C)
Ambient temperature: 14°F to 158°F (-10°C to 70°C)
Accuracy: ±0.3% typ. at 25°C
Total error band (TEB): ±1.0% typ. (-10°C to 70°C)
Nonlinearity, hysteresis (NLH): ±0.2% typ. Best Straight Line (BSL) at 25°C
Zero point and temperature compensation range: 0.04% of full scale/°F (0.02% of full scale/°C)
Long-term stability: 0.2% typ. full scale. 1 year at 25°C
Rise time: 1 ms typ. (rated pressure from 10% to 90%)
Start-up delay: 100ms
Overpressure: 15 PSI (1.03 bar)
Pressure d Burst: 30 PSI (2.07 bar)
Vibration: 6 g (25 to 2000 Hz)
Shock: 50 g / 8 ms
Construction: AISI316L stainless steel housing, pressure fitting; Ceramic, Al2O3 sensor (96%); FKM (FPM, Viton), EPDM (TPE) seals; PUR cable
Minimum cable bending radius: 1.57â€ (40 mm)
EMC compatibility: EN/IEC 61000-6-3 / GL 2012, IV, Part 7 (emission and immunity)
Weight: 12.6 oz (357 g)

Frequently Asked Questions (FAQ) about the Maretron Submersible Pressure Transducer - 0 to 3 PSI Who is the Maretron?
How to describe the transducer Maretron submersible pressure transducer - 0 to 3 PSI?
What is the exterior color of the product?
In which country is this product manufactured?
What are the dimensions and weight of the submersible pressure transducer Maretron - 0 to 3 PSI?
What is the connector type of the product?
What is the cable length?
What is the product's communication method?
What are the manufacturer's ratings for the Maretron Submersible Pressure Transducer - 0 to 3 PSI?
Who is the Maretron? Maretron products, from GPS receivers to transducers, are designed to withstand the harshest marine conditions. Maretron carefully protects all our electronic devices, even equipment below deck, in waterproof enclosuresto ensure years of reliable performance. Superior engineering, maximum precision, consistent reliability: three reasons why Maretron products are among the best in the world. How to describe the Maretron Submersible Pressure Transducer - 0 to 3 PSI? The

Maretron fluid pressure sensor transducers work with the Maretron FPM100 which will adapt up to six pressure transducers to the NMEA 2000 network. Submersible pressure transducer - 0 to 3 PSI Used for tanks up to 80" or 2M deep .n used with Maretron displays, alerts can be set so that the user can be informed of low or high tank levels. And when not on board the vessel, users. can be informed by email or SMS of the level of their tanks In addition, the levels.tanks can be stored using the Maretron data logger (VDR100) for later analysis.

Maretron Pressure transducers are not approved for use with gasoline. If you wish to use the FPM100 to monitor gasoline pressures or levels, you must obtain a pressure transducer approved for use with gasoline.

What is the exterior color of the product? Silver

Maretron fluid pressure sensor transducers work with the Maretron FPM100 which will adapt up to six pressure transducers to the NMEA 2000 network. Submersible pressure transducer - 0 to 3 PSI Used for tanks up to 80" or 2M deep When used with Maretron displays, alerts can be set so the user can be informed of low or high tank levels. When not on board the vessel, the. Users can be notified by email or text messages about their tank levels. Additionally, tank levels can be stored using the Maretron Data Logger (VDR100). ) for further analysis.

Maretron Pressure transducers are not approved for use with gasoline.To use the FPM100 to monitor gasoline pressures or levels, you must obtain a pressure transducer approved for use with gasoline.

$149

Maretron Submersible Pressure Transducer - 0 to 3 PSI

$260

Type:	Marine Navigation & Instruments \| NMEA Cables and Sensors
Supplier:	Maretron
Weight:	1.4 lbs

Shipping Weight:	1.4 lbs
Box sizes:	3.00 (h) x10.00 (l) x 11.00 (l)
Cubic Feet:	330.0
Recordable:	Yes
P65:	Yes

For detailed shipping terms, please see our shipping policy and you can find our return and refund policy here.