Newmar 12-12-3i power stabilizer Bestsellers

12-12-3i Power Stabilizer

Power sensitive electronic components with the appropriate voltage, regardless of battery condition. This stabilizing converter provides continuous, precisely regulated output over the entire usable voltage range of a battery. This avoids subjecting loads to fluctuating input voltage, which can cause shutdown, decrease performance and possibly damage sensitive circuitry.

This converter provides total input/output isolation, virtually eliminating conducted line noise and allowing the connection of negative cables. ground equipment to positive or floating ground systems, or vice versa. It can be modified for use as a battery charger, allowing them to maintain a battery at a large distance from the main voltage source, thus providing a reserve of energy in the event the main source fails. The boRobust anodized aluminum housing is ideal for marine applications.

Application benefits include:

Operate electronics at optimal input voltage, even when batteries are almost exhausted
Increase the voltage to compensate for voltage drops in long battery cables
Eliminate voltage drops during a momentary high current draw from batteries, such as during engine cranking
Eliminates voltage fluctuations from charging sources
Eliminates voltage overshoots due to sudden removal of a high current charging

Specifications:

Input voltage: 10-16
Amps input: 4
Output voltage: 13.6
Output amps (intermittent): 3
Output amplifiers (continuous): 3
Case Size (H x W x D): 3.5 x 3.5 x 1.75 inches (8.9 x 8.9 x 4.5 centimeterss)
Weight: 0.45 kg (1 lb)
Output: 12 or 24 V, nominal, see matrix
Ripple: 150 mV P-P maximum
Regulation: 1% line/load

Duty cycle ratings:

Intermittent : 20 minutes maximum operation, 20% service. The current limit is set at approx. 105% of intermittent rate.
Continuous: 24 hours, 100% duty
Idle Current: Less than 100 mA (including power "ON" light)
Operating temperature: 0 to 50 degrees C, linear derating from 100% at 40 degrees C to 50% at 50 degrees C. Thermal shutdown at 70 degrees C case temperature.
Switching frequency: 40 kHz.
Efficiency: 85% – Typical.
Isolation – Output/Chassis; Input/Chassis: 250 VDC

Mechanical specifications:

Anodized aluminum heat sink housing
Front panel terminal block
BriRugged Mounting System
Conformal Coated PC Board

Options/Factory Modifications:

Operation as battery charger (contact factory)
Parallel/redundant operation (contact factory)
High vibration mounting kit
Voltage non-standard output (contact factory)

Option: Extreme Vibration Mounting Kit

The Extreme Vibration Mounting Kit is available to protect NEWMAR power converters from extreme shock and vibration conditions when fitted to high vibration vehicles.

The kit (pictured here) replaces the standard vibration kit supplied with the unit and fits into the unit's mounting flange to act as a "super shock absorber" for the electronics in high vibration applications. It is available to fit all NEWMAR units from 2 to 70 lbs. Specify KIT–Lfor units weighing 2 to 15 lbs. and Kit-H for units weighing between 16 and 70 lbs.

This product cannot be returned to the original point of purchase. Please contact the manufacturer directly with any problems or concerns.

PRODUCT ID: 102294
SKU: NVN-102294
CSKU: CWR-102294
REWRITE : 113405 -newmar-12-12-3i-power-stabilizer
MPN: 12-12-3I
UPC:
ASIN:
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: NEWMAR 12-12-3I POWER STABILIZER
NAME_EX:
PTITLE: Newmar 12-12-3i Power Stabilizer
TYPE: Electric | DC to DC Converters
SELLER: Newmar Power
VEHICLES & PARTS> VEHICLE PARTS & ACCESSORIES> WATERCRAFT PARTS & ACCESSORIES

Category Amazon:
Gtags:

GSpecs:

Newmar 12-12-3i Power Stabilizer Product Description

12-12-3i Power Stabilizer

Power sensitive electronic components with appropriate voltage, regardless of battery status. This stabilizing converter provides continuous, precisely regulated output over the entire usable voltage range of a battery. This avoids subjecting loads to fluctuating input voltage, which can cause shutdown, decrease performance and possibly damage sensitive circuitry.

This converter provides total input/output isolation, virtually eliminating conducted line noise and allowing the connection of negative cables. ground equipment to positive or floating ground systems, or vice versa. It can be modified for use as a battery charger, allowing them to maintain a battery at a large distance from the main voltage source, thus providing udoes not reserve energy in the event of a failure of the main source. Rugged anodized aluminum housing is ideal for marine applications.

Application benefits include:

Operate electronics at optimal input voltage, even with batteries near depletion.
Raise the voltage to compensate for voltage drops on long battery cables
Eliminate voltage drops when from momentary high current discharge of batteries, such as when starting the engine
Eliminates voltage fluctuations from charging sources
Eliminates voltage overshoots due to sudden removal of high current load

Specifications:

Input voltage: 10-16
Input Amps: 4
Output Voltage: 13.6
Output Amps (Intermittent): 3
Output Amplifiers (Continuous) : 3
Case size(H x W x D): 3.5 x 3.5 x 1.75 inches (8.9 x 8.9 x 4.5 centimeters)
Weight: 1 lb. (0.45 kg)
Output: 12 or 24 V, nominal, see matrix
Ripple: 150 mV P-P maximum
Regulation: 1% line/ load

Duty Cycle Ratings:

Intermittent: 20 minutes maximum on time, 20% duty. The current limit is set at approx. 105% of tent interindex.
Continuous: 24 hours, 100% service
Idle current: less than 100 mA (including power indicator "ON )
Operating temperature: 0-50 degrees C, linear derating from 100% at 40 degrees C to 50% at 50 degrees C. Thermal shutdown at 70 degrees C case temperature. li>
Switching frequency: 40 kHz.
Efficiency: 85% – Typical.
Isolation – Output/Chassis; Input/Chassis: 250 VDC

Mechanical specifications:

Aluminum heat sink housingAnodized ium
Front panel terminal block
Robust mounting flange
Conformal coated PC board

Factory Options/Modifications:

Operation as battery charger (contact factory)
Parallel/redundant operation (contact factory)
Mounting kit for high vibration
Non-standard output voltage (contact factory)

Option: mounting kit for Extreme Vibration

The Extreme Vibration Mounting Kit is available to protect NEWMAR power converters from the extreme stresses of shock and vibration when mounted on high vibration vehicles.

The kit (pictured here) replaces the standard vibration kit supplied with the unit and fits into the unit's mounting flange. to act as a "super shock absorber" for electronics in high vibration applications. It is available to fit toUses NEWMAR units from 2 to 70 lbs. Specify KIT–L for units weighing 2 to 15 lbs. and Kit-H for units weighing between 16 and 70 lbs.

This product cannot be returned to the original point of purchase. Please contact the manufacturer directly if you have any problems or concerns.

Save $68 when you purchase the Newmar 12 -12- 3i Power Stabilizerfor only $196 from NVN Marine! Same day dispatch before 3 p.m. Technical specifications of the Newmar 12-12-3i power stabilizer

Type:	Electric \| DC to DC Converters
Supplier:	Newmar Power

Newmar 12-12-3i Power Stabilizer User ReviewsNewmar 12-12 -3i Power Stabilizer Shipping & Return

For detailed shipping policy, please see our shipping policy and YOUcan find our return and refund policy here.