Pre-cut NavPod RailMount for Simrad GO7 XSE GO7 XSR and B&G Vulcan 7R (fits 1″ or 1.25″ tubes) Boat Outfitting

Pre-cut RailMount for Simrad GO7 XSE, GO7 used for mounting an autopilot controller, navigation instrument or small chart plotter to an existing protective mount. Fits any 1", 1.125" or 1.25" diameter tube. A stainless steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing when you are sitting under the vehicle on a rainy day All wiring runs from the NavPod, down the center of the stainless steel arm (the available space is 0.75″ inside the narrowest part of the arm, so keep this in mind when planning your cable route; most transducer cables will not pass through the arm), and into the pedestal protection This application provides a clean, sturdy installation.for electronics, without having to replace the base guard.

The rail mounts are designed for all common standard-sized instruments, as well as 7 and 9 inch chart plotters.

Structural Rigidity –Gen3 improvements now include thicker acrylic-coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.

Waterproof Seal – All RailMount NavPods are manufactured with a double seal system providing an excellent seal. This seal provides the best protection for your marine electronics. THENavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The internal Poron Microcell polyurethane gasket is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel – We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. Tamper-resistant nickel-chrome-plated stainless steel screws provide security combined with a bit of style!

Commitment tos quality – We stand behind our commitment by offering a 10-year warranty on all new NavPods Gen3.

PRODUCT ID: 92198
SKU: NVN-92198
CSKU: CWR-92198
REWRITE: 103309-navpod-railmount-pre-cut-f-simrad- go7-xse-go7
MPN: RMX4400-12
UPC:
ASIN:
WSKU: NAVRMX440012
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: NavPod RailMount Pre-Cut f/Simrad GO7 XSE, GO7 XSR & B&G Vulcan 7R (fits Tubi 1″ or 1.25″ng)
NAME_EX: PRECUT NAVPOD RAIL MOUNT FOR B&G VULCAN 7R/SIMRAD GO7-XSR
PTITLE: Precut NavPod RailMount for Simrad GO7 XSE, GO7 XSR and B&G Vulcan 7R (fits 1″ or 1.25″ tubes)
TYPE: Boat outfitting | Display Mounts
SELLER: NavPod
ELECTRONICS> MARINE ELECTRONICS

NavPod RMX4400-12 RailMount for Simrad Go7-xsr

Gtags:

Fish finder

GSpecs:

NavPod Pre-cut RailMount for Simrad GO7 XSE, GO7 7R (fits 1″ or 1.25″ tubes)

RailMount NavPods are best used to mount an autopilot control, navigation instrument, or small chartplotter on an existing base of protection. Fits any 1", 1.125" or 1.25" diameter tube. A stainless steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing when you are sitting under the vehicle on a rainy day All wiring runs from the NavPod, down the center of the stainless steel arm (the available space is 0.75″ inside the narrowest part of the arm, so keep this in mind when planning your cable route; most transducer cables;will not pass through the arm), and into the protection of the base. This application provides a clean, sturdy installation for electronics, without the replacement of the base guard.

RailMount brackets are designed for all common standard-sized instruments, as well as chartplotters 7 and 9 inches.

Structural Rigidity – Gen3 enhancements now include thicker gauge acrylic coated ABS material. which improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. Acrylic cap protects ABS from UV and its potentially damaging effects on plastic.

Waterproof seal – All RailMount NavPods are manufacturedés with a double seal system offering excellent sealing. This seal provides the best protection for your marine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The intern's Poron Microcell polyurethane gasket is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel – We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our NavPod from thetraditional series. Tamper-proof nickel-chrome-plated stainless steel screws provide security combined with a little style!

Commitment to quality – We stand behind our commitment by offering a 10-year warranty on all new NavPods Gen3.

Frequently asked questions (FAQ) about the NavPod RailMount Pre-Cut f/Simrad GO7 XSE, GO7 XSR and B&G Vulcan 7R (fits 1″ tubes or 1.25″) Who is the NavPod?
How to describe the NavPod RailMount Pre-Cut f/Simrad GO7 XSE, GO7 XSR and B&G Vulcan 7R (fits 1″ or 1.25″ tubes)?
Who is the NavPod? Navpod is a better way to mount your fishfinder, radar or GPS. The unique watertight seal, build quality and attractive design make the best-built instrument housing ever available to the marine industry. Features of all Navpods include waterproof silicone seal, tamper-proof clips for added security and convenienceed, concealed wiring and clean installation for easy access. How to describe the NavPod RailMount Pre-Cut f/Simrad GO7 XSE, GO7 XSR & B&G Vulcan 7R (fits 1″ or 1.25″ Tube)? "

NAVPOD RMX4400-12 Railmount

Model: RMX4400-12

Pre-cut RailMount for Simrad GO7 XSE, GO7 XSR/B&G Vulcan 7R ( fits 1? or 1.25? tubes)

Rail mount NavPod are best used for mounting an autopilot control, of a navigation instrument or a small chart plotter on an existing system. Fits any 1" or 1.25" diameter tube. A chrome-plated, nickel-plated stainless steel arm. is used to mount a NavPod The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle on a rainy day. All wiring runs from the NavPod, descends into the center of the stainless steel arm and arrives in the share protectionTHE. This application provides a clean, sturdy installation for electronics without replacing the base guard.

Rail mounts are designed for all popular standard size instruments as well as chart plotters. 7 and 9 inches.

Structural Rigidity — Gen3 enhancements now include thicker acrylic-coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of acrylic and ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.

Watertight seal — All NavPod RailMounts are manufactured with a double seal system providing an excellent starwaterproofness. This seal offers the best protection for your marine electronics. The NavPod are designed to withstand the harshest wet offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The internal Poron Microcell polyurethane gasket is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The gasket will continue to do its job.

Chrome Nickel Plated Stainless Steel — We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. Tamper-proof screwsNickel-plated, chrome-plated stainless steel offer safety combined with a bit of style!

Specifications

Overall size
Height
in	10.5
cm	26.7
Width
in	12.5
cm	31.8
Depth
in	5.92
cm	15.0
Usable face
Height
in	6
cm	15.2
Width	8.75
cm	22 ,2
Depth
in	3.25
cm	8.3
Maximum cutout
Height
in	5.5
cm	14.0
Width
in	8.625
cm	21.9

"

Save $158 when you purchase the pre-cut NavPod RailMount for Simrad GO7 XSE, GO7 XSR and B&G Vulcan 7R (fits 1″ or 1.25″)for only $381 at NVN Marine Same day shipping before 3pm NavPod RailMount Pre-Cut f/Simrad GO7 XSE, GO7 XSR and B&G Vulcan 7R (fits 1″ or 1.25″ tubes) Technical Specifications

Type:	Boat Display Racks
Supplier:	NavPod

Pre-cut NavPod RailMount for Simrad GO7 XSE , GO7 /p>