PSS shaft seal 1" shaft 2" tube Marine Hardware
PSS Shaft Seal 1" Shaft 2" TubeShaft Diameter: 1"
Tube Diameter: stern post (D): 2"
Total length (A): 6.975"
Total length (tablet) (Tablet A): 6.225 "
Rotor Diameter (B): 2.375"
Carbon Cuff Diameter (C): 2"
Rear Cuff Length (E): 1.5"
The PSS shaft seal is the best-selling marine mechanical seal in the world and is installed as standard equipment by many many of the world's leading boat builders/yards The PSS shaft seal is also recognized as the leading retrofit seal (aftermarket) in the global market. /boat yards recognize the benefits and value of installing PSS as it eliminates the maintenance, constant adjustment and costs associated with the traditional packing type.PSS shaft protector helps eliminate water in the bilge (100% waterproof) and wear on the propeller shaft. It installs easily and is available for shafts ranging from 3/4" (20 mm ) to 6" (150 mm).
The PSS shaft seal is a mechanical seal created between the flat surfaces of the rotating stainless steel rotor and the fixed carbon flange. The carbon fixed bridle is attached to the ship's stern tube with hose clamps and the carbon bridle is attached to the front of the bellows with hose clamps. The stainless steel rotor is mounted on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is attached to the shaft with set screws. This compression (preload) maintains contact between the faces and allows the PSS to compensate for propeller thrust. The carbon flange is bored larger than the diameter of the shaft, allowing it to "float" around the shaft and thus compeFix most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two O-rings that are recessed into the collar bore. These O-rings rotate with the stainless steel shaft and rotor and experience no wear during operation.
**As with any rubber hose below the waterline, PSS bellows must be inspected regularly for signs of wear, aging or chemical deterioration. PYI suggests, as preventative maintenance, that the PSS bellows be replaced every six years. When replacing the bellows, it is recommended to also replace the stainless steel rotor O-rings and adjustment screws. acid fumes will accelerate rubber deterioration, as will an ozonator.
The maintenance kit includes the items you need to properly maintain your PSS shaft seal.Kit includes one (1) PSS and two (2) bellows. O-rings, five (5) set screws, four (4) new hose clamps and an Allen key.
A sealing surface is formed between the plane of the stainless steel ro.rotor and the fixed carbon flange. The carbon fixed flange is connected to...
PRODUCT ID: 50830
SKU: NVN-50830
CSKU: CWR-50830
REWRITE: 61941-pss-shaft-joint-1-shaft - 2 tubes
MPN: 02-100-200
UPC: 839662007009
ASIN: B007SNUPWU
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: PSS Shaft Seal 1" Shaft 2" Tube
NAME_EX: PSS SHAFT SEAL 1" SHAFT 2" TUBE
PTITRE: PSS Shaft Seal 1" Shaft 2" tube
TYPE: Marine hardware | Shaft Seals
SELLER: PSS Shaft Seal
SPORTING GOODS> OUTDOOR RECREATION> BOATING & WATER SPORTS
Sports
PSS Shaft Seal 1" Shaft 2" Tube
Amaz Categoryon: Sports
Gtags:
GSpecs:
PSS Shaft Seal 1" Shaft 2" Tube Product Description PSS Shaft Seal 1" Shaft 2" Tube
Shaft Diameter: 1"
Stern tube diameter (D): 2"
Overall length (A): 6.975"
Length total (compressed) (Compressed A): 6.225"
Rotor diameter (B): 2.375"
Carbon sleeve diameter (C): 2"
Rear Sleeve Length (E): 1.5"
PSS Shaft Seal is the mechanical seal best-selling marine seal in the world and is installed as standard equipment by many of the world's most renowned boat builders/yards. The PSS shaft seal is also recognized as the leading retrofit (aftermarket) seal on the market. Worldwide Certified by Bureau Veritas, ABS and Rina: Boat builders/yards recognize the benefits and value of installing PSS as it eliminates the hassle of maintenance, constant adjustment and cost associated with stuffing boxes.traditional pes. Besides these benefits, the PSS shaft seal helps eliminate water in the bilge (100% watertight) and propeller shaft wear. The PSS shaft seal can be easily retrofitted and is available for shafts ranging from 3/4" (20 mm) to 6" (150 mm).
The PSS shaft seal is a mechanical face. seal that is created between the flat surfaces of the rotating stainless steel rotor and the fixed carbon flange. The carbon fixed bridle is attached to the ship's stern tube with hose clamps and the carbon bridle is attached to the front of the bellows with hose clamps. The stainless steel rotor is mounted on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is attached to the shaft with set screws. This compression (preload) maintains contact between the faces and allows the PSS to compensate for propeller thrust. The carbon flange is reamedlarger than the diameter of the shaft, which allows it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two O-rings recessed into the collar bore. These O-rings rotate with the stainless steel shaft and rotor and experience no wear during operation.
**As with any rubber hose below the waterline, PSS bellows must be inspected regularly for signs of wear, aging or chemical deterioration. PYI suggests, as preventative maintenance, that the PSS bellows be replaced every six years. When replacing the bellows, it is recommended to also replace the stainless steel rotor O-rings and adjustment screws. acid vapors will accelerate the deterioration of the rubber, as will an ozonator.
The maintenance kitnance includes the items you need to properly maintain your PSS shaft seal. Kit includes one (1) PSS and two (2) bellows. O-rings, five (5) set screws, four (4) new hose clamps and an allen wrench.
A sealing surface is formed between the plane of the rotating stainless steel rotor and the fixed carbon flange. The carbon fixed flange is connected to...
PSS Shaft Seal 1" Shaft 2" Tube Related ProductsPSS Shaft Seal Maintenance Kit 1" Shaft 2" Tube
Frequently Asked Questions (FAQ) about PSS Shaft Seal, 1" Shaft, 2" Tube, Who is PSS Shaft Seal?
How to describe PSS Shaft Seal PSS shaft, 1" shaft, 2" tube?
Who is the PSS shaft Joint? The PSS Shaft Seal is the world's best-selling marine mechanical seal and is installed as standard equipment by many of the world's leading shipyards and boat builders. The PSS shaft seal isalso recognized as the leading retrofit (aftermarket) seal in the global market. How to describe PSS Shaft Seal 1" Shaft 2" Tube? A sealing surface is formed between the plane of the rotating stainless steel rotor and the carbon fixed flange. The fixed carbon flange is connected to...
Save $75 when you purchase the PSS Shaft Seal 1" Shaft 2" Tube for only $301 from NVN Marine! Same day dispatch before 3 p.m. PSS Shaft Seal 1" Tube 2" Shaft Videos PSS Shaft Seal 1" Tube 2" Shaft Technical Specifications
| Type: | Material sailor | Shaft Seals |
|---|---|
| Supplier: | PSS Shaft Seal |
| Weight: | 2.5 lbs |
| Product Brochure: | Download PDF |
| Product installation: | Download PDF |
| Shipping Weight: | 2.5 lb |
|---|---|
| Box sizes: | 5.00 (h) x 6.00 (w ) x 9.00 (l) |
| Cubic feet: | 270.0 |
| Returnable: | Yes |
To know the conditions of For detailed shipping details, please see our shipping policy and you can find our return and refund policy here.
