Shaft seal PSS 1" shaft 1-½" tube Marine Hardware

PSS Shaft Seal 1" Shaft 1-1/2" Tube

Shaft Diameter: 1"
Diameter of stern tube (D): 1-1/2" to 1-5/8"
Overall length (A): 6.975"
Total length (compressed) (Compressed A): 6.225"
Rotor diameter (B): 2.375"
Carbon cuff diameter (C) : 2"
Rear cuff length (E): 1.5"

PSS shaft seal is the best-selling marine mechanical seal in the world and is installed as standard equipment by many manufacturers. most renowned boat builders/yards in the world. PSS shaft seal is also recognized as the leading retrofit (aftermarket) seal in the global market. Certified by Bureau Veritas, ABS and Rina: Boat builders/yards recognize the benefits and value of installing PSS as it eliminates the maintenance, constant adjustment and costs associated with traditional cable glands. Besides these beforeages, PSS shaft seal helps eliminate water in the bilge (100% waterproof) and propeller shaft wear. The PS S shaft seal can be easily retrofitted and is available for shafts ranging from 3/4" (20 mm) to 6" (150 mm).

The shaft seal PSSis a mechanical seal. which is created between the flat surfaces of the rotating stainless steel rotor and the fixed carbon flange. The carbon fixed bridle is attached to the ship's stern tube with hose clamps and the carbon bridle is attached to the front of the bellows with hose clamps. The stainless steel rotor is mounted on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is attached to the shaft with set screws. This compression (preload) maintains contact between the faces and allows the PSS to compensate for propeller thrust. The carbon flange is reamed larger than the diameter of theshaft, which allows it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings which are recessed into the collar bore. These O-rings rotate with the stainless steel shaft and rotor and experience no wear during operation.

**As with any rubber hose below the waterline, PSS bellows must be inspected regularly for signs of wear, aging or chemical deterioration. PYI suggests, as preventative maintenance, that the PSS bellows be replaced every six years. When replacing the bellows, it is recommended to also replace the stainless steel rotor O-rings and adjustment screws. acid fumes will accelerate the deterioration of the rubber, as will an ozonator.

The maintenance kit includes the items you needyou need to properly maintain your PSS shaft seal. Kit includes one (1) PSS and two (2) bellows. O-rings, five (5) set screws, four (4) new hose clamps and an Allen key.

PSS Type A shaft seal is a mechanical end seal. The sealing surface is formed between the plane of the stainless steel rotating rotor and the fixed carbon fiber bearing.
PRODUCT ID: 50827
SKU: NVN-50827
CSKU: CWR-50827
REWRITE: 61938-pss-shaft-joint-1-shaft-1-tube
MPN: 02- 100-112
UPC: 839662006972
ASIN: B00MYT4S12
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: PSS Shaft Seal 1" Shaft 1-½" Tube
EX_NAME: PSS SHAFT SEAL 1" SHAFT 1 1/2" TUBE
PTITRE: PSS Shaft Seal 1" Shaft 1-½" Tube
TYPE : Marine Hardware | Shaft Seals
SUPPLIER: PSS Shaft Seal
SPORTING GOODS> OUTDOOR RECREATION> BOATING & WATER SPORTS
Ca

PSS (Packless Sealing System) Shaft Seal - 1" Shaft

Gtags:

GSpecs:

PSS Shaft Seal, 1" Shaft, 1-½" Tubing Product Description PSS Shaft Seal, 1" Shaft, 1-1/2" Tubing

Shaft Diameter: 1"
Stern Tube Diameter (D): 1-1/2" to 1-5/8"
Total length (A): 6.975"
Total length (compressed) (Compressed A): 6.225"
Rotor diameter ( B): 2.375"
Carbon cuff diameter (C): 2"
Rear cuff length (E): 1. 5"

PSS Shaft Seal is the best-selling marine mechanical seal product worldwide and is installed as standard equipment by many of the world's leading boat builders/yards. most famous in the world. PSS shaft seal is also recognized as the leading retrofit (aftermarket) seal in the global market. Certified by Bureau Veritas, ABS and Rina: Boat builders/yards recognize the benefits and value of installing PSS as it eliminates maintenance, lconstant adjustment and costs associated with traditional cable glands. In addition to these advantages, the PSS shaft seal helps eliminate water in the bilge (100% waterproof) and wear on the propeller shaft. The PSS shaft seal can be easily retrofitted and is available for shafts ranging from 3/4" (20 mm) to 6" (150 mm).

The PSS shaft seal is a mechanical face. seal that is created between the flat surfaces of the rotating stainless steel rotor and the fixed carbon flange. The carbon fixed bridle is attached to the ship's stern tube with hose clamps and the carbon bridle is attached to the front of the bellows with hose clamps. The stainless steel rotor is mounted on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is attached to the shaft with set screws. This compression (preload) maintains contact between the faces and allows the PSS to compensate for the ppropeller thrust. The carbon flange is bored larger than the diameter of the shaft, allowing it to "float" around the shaft and thus compensate for most misalignments and vibration issues. The stainless steel collar is sealed to the shaft by two O-rings recessed into the collar bore. These O-rings rotate with the stainless steel shaft and rotor and experience no wear during operation.

**As with any rubber hose below the waterline, PSS bellows must be inspected regularly for signs of wear, aging or chemical deterioration. PYI suggests, as preventative maintenance, that the PSS bellows be replaced every six years. When replacing the bellows, it is recommended to also replace the stainless steel rotor O-rings and adjustment screws. acid vapors will accelerate the deterioration of the rubber, while coeven an ozonator.

The maintenance kit includes the items you need to properly maintain your PSS shaft seal. Kit includes one (1) PSS and two (2) bellows. O-rings, five (5) set screws, four (4) new hose clamps and an allen wrench.

PSS Type A shaft seal is a mechanical seal. The sealing surface is formed between the plane of the stainless steel rotating rotor and the fixed carbon fiber bearing.

PSS Shaft Seal 1" Shaft 1-½" Tube Related Products PSS Shaft Seal Service Kit 1" Shaft 1-1/2" Tube

Frequently Asked Questions (FAQ) About PSS Shaft Seal 1" Shaft 1-½" Tube Who is PSS Shaft Seal?
How to describe PSS Shaft Seal 1" Shaft 1-½" Tube?
Who is the PSS Shaft Joint? The PSS shaft seal is the best-selling marine mechanical seal in the world and is installed as standard equipment by many shipyards.endorsements and boat builders among the most renowned in the world. The PSS Shaft Seal is also recognized as the leading retrofit (aftermarket) seal in the global market. How to describe PSS shaft seal for 1" shaft and 1-½" tube? PSS Type A Shaft Seal is a mechanical end seal. The sealing surface is formed between the plane of the stainless steel rotating rotor and the fixed carbon fiber bearing.

Save $40 when you purchase the PSS Shaft Seal 1" Shaft 1-½" Tube for only $336 at NVN Marine! Same day dispatch before 3 p.m. PSS Shaft Seal 1" Shaft 1-½" Tube Videos PSS Shaft Seal 1" Shaft 1-½" Tube Technical Specifications

Type:	Marine Equipment \| Shaft Seals
Supplier:	PSS Shaft Seal
Weight:	2.4 lbs
Product brochure:	Download PDF
Product installation:	Download PDF

PSS Shaft Seal 1"; Shaft 1-½" Tube User ReviewsPSS Shaft Seal 1" Shaft 1-½" Tube Shipping & Returns

Shipping Weight:	2.4 lbs
Box Sizes:	5.00 (h) x 6.00 (w) x 9.00 (l)
Cubic feet :	270.0
Returnable:	Yes