Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC Electrical
BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it no longer has enough power left to crank the engine. Battery Protect is a unidirectional device. It can only handle current in one direction, so either current to a load or current coming from a charger, but not both currents at the same time. Additionally, current can only flow from the battery terminal to the charging terminal. When used with a load, the battery connects to the Battery terminal, and when used with a charger, the charger connects to the Battery terminal.BatteryProtect BP-220 - 220AMP - 6-35 VDC
Features:
- The BatteryProtect disconnects the battery from unloaded loads essential before it is completely discharged (which will damage the battery) ou before there is no longer enough power left to start the engine.
- 12/24V Auto Range The BatteryProtect automatically senses system voltage
- Simplified Programming The BatteryProtect can be configured to turn on/off at several different voltages. The seven segment display will indicate which setting has been chosen.
- A special setting for Li-ion batteries. In this mode, the BatteryProtect can be controlled by the VE.Bus BMS. Note: The BatteryProtect can also be used as a load switch between a battery charger and a Li-ion battery. See connection diagram in the manual.
- Ultra low current consumption This is important in the case of Li-ion batteries, especially after a low voltage shutdown. Please see our Li-ion battery datasheet and VE.Bus BMS manual for more information.
- Overvoltage protection To avoid overvoltagedamage sensitive loads due to overvoltage, the load is disconnected whenever the DC voltage exceeds 16 V respectively 32 V.
- Ignition proof No relays but MOSFET switches, and therefore no sparking.
- Delayed Alarm Output The alarm output is activated if the battery voltage drops below the preset disconnect level for more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit resistant open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnection and delayed reconnection The load will be disconnected 90 seconds after the alarm is activated. If the battery voltage increases again to the connection threshold during this period (after starting the engine for example), the load will not be disconnectedee. The load will be reconnected 30 seconds after the battery voltage increases beyond the preset reconnection voltage.
Warranty Information
This product can expose you to chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. For more information, go to P65Warnings.ca.gov.
Please contact your dealer for any returns, repairs or problems. support related to this product.BatteryProtect BP-220- 220AMP-6-35 VDC Features: BatteryProtect will disconnect the battery from non-essential loads before the battery is completely discharged (this will damage the battery ...
PRODUCT ID: 82915
SKU: NVN-82915
CSKU: CWR-82915
REWRITE: 94026-victron-batteryprotect-bp-220-220amp-6-35
MPN: BPR000220400
UPC: 8719076021452
ASIN: B01KIF2DWO
WSKU:
SSKU: VIC-BPR000220400
KSKU: VICBPR0002204
GSKU: BPR000220400
MSKU:
LSKU:
NAME: Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC
NAME_EX: VICTRON BATTERYPROTECT 12/24V-220A
PTITRE: Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC
TYPE: Electric | Battery Management
SUPPLIER: Victron Energy
VEHICLES & PARTS> VEHICLE PARTS & ACCESSORIES> POWERWATER PARTS & ACCESSORIES
CE
Victron BatteryProtect BP-220 -220AMP - 6 -35 VDC [BPR000220400]
Victron Energy Marine BPR000220400 BatteryProtect 12/24 V -220 A
CE
Gtags:
| Victron Energy | |
| Rechargeable |
GSpecs:
Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC Product Description The BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it There is enough power left to start the engine. Battery Protect is a unidirectional device. It can only handle current in one direction, so either current to a load or current coming from a charger, but not both currents at the same time. Additionally, current can only flow from the battery terminal to the charging terminal. When used with a load, the battery connects to the Battery terminal, and when used with a charger, the charger connects to the Battery terminal.
BatteryProtect BP-220 - 220AMP - 6-35 VDC
Features:
- The BatteryProtect disconnects the battery of non-essential loadss before it is completely discharged (which would damage the battery) or before it is insufficientThere is no more power left to start the engine.
- 12/24V Auto Range The BatteryProtect automatically senses the system voltage
- Simplified Programming The BatteryProtect can be configured to turn on/off at several different voltages. The seven segment display will indicate which setting has been chosen.
- A special setting for Li-ion batteries. In this mode, the BatteryProtect can be controlled by the VE.Bus BMS. Note: The BatteryProtect can also be used as a load switch between a battery charger and a Li-ion battery. See connection diagram in the manual.
- Ultra low current consumption This is important in the case of Li-ion batteries, especially after a low voltage shutdown. Please see our Li-ion battery datasheet and VE.Bus BMS manual for details.read more information.
- Overvoltage protection To avoid damage to sensitive loads due to overvoltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V.
- Proof of ignition No relay but MOS FET switches, and therefore no sparking.
- Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnection level for more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit resistant open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnection and delayed reconnection The load will be disconnected 90 seconds after the alarm is activated. If the battery voltage increases again to the connection threshold during this period (afterstarting the engine for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage increases beyond the preset reconnection voltage.
Warranty Information
WARNING:This product can expose you to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information,
Please contact your dealer for any returns, repairs, or support issues related to this product.BatteryProtect BP-220- 220AMP-6-35 VDC Features: BatteryProtect will disconnect the battery from non-essential loads before the battery is completely discharged (this will damage the battery...
Victron BatteryProtect BP -220 - 220AMP - 6 -35 VDC Related ProductsAncor Black 4 Battery CableAWG - 25'
4 AWG Red Ancor Battery Cable - 25'
4 AWG Yellow Ancor Battery Cable - 25'
2 AWG Black Ancor Battery Cable - 25'
Ancor Red 2 AWG Battery Cable - 25'
Ancor Yellow 2 AWG Battery Cable - 25'
Ancor Heavy Duty Lugs - 2 Gauge Wire - 5/16" Post - 2 Pack
Ancor Heavy Duty Lugs - 2 Gauge Wire - 5/16" Post - 25 Pack
Ancor Heavy Duty Lugs - 1 Gauge Wire - 5/16" Post - 2 Pack
Ancor Heavy Duty Lugs service - 1 gauge wire - 5/16" post - Pack of 25
Frequently asked questions (FAQ) about Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC Who is Victron Energy?
How to describe Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC?
What are the manufacturer's ratings for Victron BatteryProtect BP-220 - 220AMP - 6- 35 VDC?
Who is Victron Energy? b>Victron Energy is a global company renowned for its technical innovation, reliabilityity and its manufacturing quality. Victron products, which excel in the efficient combination of two or more distinct energy sources, are recognized internationally as the professional choice in resilient energy. Victron products include sine wave inverters, sine wave inverters/chargers, battery chargers, DC/DC converters, transfer switches, battery monitors and more. How to describe Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC? BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it no longer has enough power left to crank the engine. Battery Protect is a unidirectional device. It can only handle current in one direction, so either current to a load or current coming from a charger, but not both currents at the same timetime. Additionally, current can only flow from the battery terminal to the charging terminal. When used with a load, the battery connects to the battery terminal, and when used with a charger, the charger connects to the battery terminal.What are the ratings of the manufacturer regarding Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC? BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it no longer has enough power left to crank the engine. Battery Protect is a unidirectional device. It can only handle current in one direction, so either current to a load or current coming from a charger, but not both currents at the same time. Additionally, current can only flow from the battery terminal to the charging terminal. When used with a charge, the battery connects tothe Battery terminal, and when used with a charger, the charger connects to the Battery terminal.
Save $15 when you purchase the Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC for only $87 at NVN Marine! Same day dispatch before 3 p.m. Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC Videos Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC Technical specifications
| Type: | Electric | Battery management |
|---|---|
| Supplier: | Victron Energy |
| Weight: | 2.5 lbs |
| User Guide: | Download PDF |
| Product installation: | Download PDF |
| Shipping weight: | 2.5 lbs |
|---|---|
| Box sizes: | 3.00 (h) x 6.00 (w) x 6.00 (w) |
| Cubic feet: | 108.0 |
| P65: | Yes |
For detailed shipping terms, please see our shipping policy and you can find our return and refund policy here.
