Victron Smart BatteryProtect - 220AMP - 6-35 VDC - Bluetooth Compatible Electrical

Smart BatteryProtect - 220 AMP - 6-35 VDC - Bluetooth Compatible

Features:

Protects the battery against excessive discharge and can be used as a system on/off switch. Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has enough power remaining to crank the engine. The on/off input can be used as a system on/off switch.
12/24V Auto Range The Smart BatteryProtect automatically detects the system voltage only once.
Bluetooth: Programming Made Easy When using Bluetooth to program the Smart BatteryProtect, any required engagement/disengagement levels can be set. Alternatively, one of nine preset engagement/disengagement levels can be set with the pr pinprogramming (see manual). If necessary, Bluetooth can be disabled.
A special setting for Li-ion batteries. In this mode, the BatteryProtect can be controlled by the VE.Bus BMS. Note: The BatteryProtect can also be used as a load switch between a battery charger and a Li-ion battery. See the connection diagram in the manual.
Ultra-low current consumption This is important in the case of Li-ion batteries, especially after a low voltage shutdown. Please see our Li-ion battery datasheet and VE.Bus BMS manual for more information.
Overvoltage protection To avoid damage to sensitive loads due to overvoltage, the load is disconnected whenever the DC voltage exceeds 16.3 V respectively 32.6 V.
Anti-ignition No relays but MOSFET switches, and therefore no sparks.
Delayed alarm output The alarm outputme is activated if the battery voltage drops below the preset disconnection level for more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit resistant open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.
Delayed Load Disconnect and Delayed Reconnect The load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connection threshold during this period (after starting the engine for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage increases beyond the preset reconnection voltage.

Warranty Information

This product can expose you to chemicals known to the State of California to cause cancer, defects, or other reproductive harm. For more information,

Please contact your dealer for any return, repair, or support issues related to this product.

Smart BatteryProtect-220AMP- 6-35 VDC-with Bluetooth function: prevents battery from excessive discharge, can be used as system on/off switch. Smart...
PRODUCT ID: 82919
SKU: NVN-82919
CSKU: CWR-82919
REWRITE: 94030-victron-smart-batteryprotect-220amp-6-35
MPN: BPR122022000
UPC: 8719076041269
ASIN: B07MXH2TVX
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: Victron Smart BatteryProtect - 220AMP - 6-35 VDC - Bluetooth Compatible
EX_NAME: VICTRON SMART BATTERYPROTECT 12/24V-220A
PTITLE: Victron Smart BatteryProtect - 220AMP - 6-35 VDC - Bluetooth Compatible
TYPE: Electric | Battery Management
SUPPLIER: Victron Energy
VEHICLES & PARTS> VEHICLE PARTS & ACCESSORIES> WATERCRAFT PARTS & ACCESSORIES
CE
Victron Smart BatteryProtect - 220AMP - 6-35 VDC - Bluetooth C. [BPR122022000]
Victron Energy Marine BPR122022000 Smart BatteryProtect with Bluetooth 12/24V -220A
CE
Gtags:

24 volts

GSpecs:

Victron Smart BatteryProtect - 220AMP - 6-35 VDC - Bluetooth Compatible Product description

Smart BatteryProtect - 220AMP - 6-35 VDC - Bluetooth Compatible

Features:

Protects the battery from over-discharge and can be used as a system on/off switch. The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery). the battery) or before there is no longer enough power left to start the engine. The on/off input can be used as a system on/off switch.
12/24V Auto Range The Smart BatteryProtect automatically detects the system voltage only once.
Bluetooth: programming made simple When using Bluetooth to program the Smart BatteryProtect, all required levels of engagement/disengagement can be challengednis. Alternatively, one of nine preset engagement/disengagement levels can be set with the programming pin (see manual). If necessary, Bluetooth can be disabled.
A special framework for Li-ion Batteries In this mode, the BatteryProtect can be controlled by the VE.Bus BMS. Note: The BatteryProtect can also be used as a load switch between a battery charger and a Li-ion battery. See the connection diagram in the manual.
Ultra-low current consumption This is important in the case of Li-ion batteries, especially after a low voltage shutdown. Please see our Li-ion battery datasheet and VE.Bus BMS manual for more information.
Overvoltage protection To avoid damage to sensitive loads due to overvoltage, the load is disconnected whenever the DC voltage exceeds 16.3 V respectively 32.6 V.
Anti-ignition No relbut MOSFET switches, and therefore no sparks.
Delayed Alarm Output The alarm output is activated if the battery voltage drops below the preset disconnect level for more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit resistant open collector output to the negative(minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.
Delayed Load Disconnect and Delayed Reconnect The load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connection threshold during this period (after starting the engine for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage increases beyond the reconnect voltage

Warranty Information

This product can expose you to chemicals known to the State of California as causing cancer, birth defects, or other reproductive harm. For more information,

Please contact your dealer for any return, repair, or support issues related to this product.

Smart BatteryProtect-220AMP- 6-35 VDC-with Bluetooth function: prevents the batbattery from over discharge, can be used as system on/off switch. Smart ...

Victron Smart BatteryProtect - 220AMP - 6-35 VDC - Bluetooth Compatible Related ProductsAncor Black Battery Cable 4 AWG - 25'
Ancor Red Battery Cable 4 AWG - 25'
4 AWG Yellow Ancor Battery Cable - 25'
2 AWG Black Ancor Battery Cable - 25'
Red Ancor Battery Cable2 AWG - 25'
Ancor Yellow Battery Cable 2 AWG - 25'
Ancor Heavy Duty Lugs - 2 Gauge Wire - 5/16" Post - 2 Pack
Ancor Heavy Duty Lugs - 2 Gauge Wire - 5/16" Post - 25 Pack
Ancor Heavy Duty Lugs - 1 Gauge Wire - 5/16" Post - 2 Pack
Ancor Heavy Duty Lugs - 1 Gauge Wire 1 - 5/16" Post - Pack of 25

Frequently Asked Questions (FAQ) about Victron Smart BatteryProtect - 220AMP - 6-35 VDC - Bluetooth Compatible Who is Victron Energy ?
How to describe Victron Smart BatteryProtect - 220AMP - 6-35 VDC - Bluetooth compatible?
Who is Victron Energy? Victron Energy is a global company renowned for its technical innovation, reliability and build quality. Victron products, which excel at efficiently combining two or more distinct energy sources, are recognized internationally as the professional choice for storage systemsresilient energy. Victron products include sine wave inverters, sine wave inverters/chargers, battery chargers, DC/DC converters, transfer switches, battery monitors and more. How to describe Victron Smart BatteryProtect - 220AMP - 6-35 VDC - Bluetooth Compatible? Smart BatteryProtect-220AMP-6-35 VDC-with Bluetooth function: prevents the battery from over-discharging, can be used as a system on/off switch. Smart...

Save $18 on the purchase of the Victron Smart BatteryProtect - 220 A - 6-35 VDC - Bluetooth Compatible for only $105 from NVN Marine! Same day dispatch before 3 p.m. Victron Smart BatteryProtect - 220AMP - 6-35 VDC - Bluetooth-enabled technical specifications

Type:	Electric \| Battery management
Supplier:	Victron Energy
Weight:	2.1 lbs
User Guide:	Download PDF

Victron Smart BatteryProtect - 220AMP - 6-35 VDC - Bluetooth compatible User reviewsVictron Smart BatteryProtect - 220AMP - 6-35 VDC - Bluetooth Compatible Shipping & Returns

Shipping Weight:	2.1 lbs
Box sizes:	3.00 (h) x 6.00 (w) x 6.00 (w)
Cubic feet:	108.0
P65:	Yes

For detailed shipping terms, please see our Shipping Policy and you can find our return policy and refund policy here.