Lenco Auto Glide Boat Leveling System for Single Actuator Tab Systems with Existing NMEA 2000 Boat Outfitting

Auto Glide Boat Leveling System - Single Actuator Kit without GPS Antenna or Network - For boats equipped with existing NMEA 2000 networks. A true automatic boat control/trim tab system that actually works - completely and automatically. The Auto Glide system controls your trim tabs from the moment you leave your dock until you return home! Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimal operating angle is determined during the setup process after installing your Auto Glide system. Imagine that your boat's running angle is measured 25 times per second and that data is used by the new Auto Glide control box to: - Automatically move your boat into themost effective running angle. - Reduce the rise of the bow of your boat during the hole. shooting mode. - Eliminates bow porpoising (bow bounce). - Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency. Note: Auto Glide does not control the "trim" function of your engine(s). Remember to use the trim function exactly as you would in the normal operation of your boat. The Auto Glide control box (brain) consists of gyroscopes, accelerometers and very sophisticated new patented software. The Auto Glide has 3 automatic operating modes, 4 automatic settings and 2 manual operating modes. Although you will likely keep your Auto Glide in automatic mode, you can immediately switch to manual mode by simply pressing one of the 4 up/down buttons on the keypad.er. All of these functions are fully explained in our Owner's Manual B/Operating Instructions.

Attributes of the Lenco 15504101

Compatibility: Single actuator compensating lights and boats without existing NMEA 2000 networks
Type: Keypad

Lenco 15504101 Features and Benefits

Automatic pitch and roll corrections
Automatically adjusts the boat to the most fuel-efficient position.
Manual control at the touch of a button.
Integrated automatic compensator retraction.
Fully waterproof keypad and control box
Three custom settings
2-year limited warranty

Installation instructions Lenco 15504101

Auto Glide Quick Reference Guide_TCHDAT.pdf
15504-101_TCHDAT.pdf

Auto Glide Boat Leveling System for single actuator tab systems with existing NMEA 2000

A true automatic boat control / trim tab control system that actually works - completely and automatically!

The Auto Glide system controls your trim tabs from the moment you leave your dock to your back home!

Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs according to your needs. This optimal running angle is determined during the setup process after installing your Auto Glide system.

Imagine your boat's running angle is measured 25 times per second and that data is used by the new Auto Glide control box to:

Automatically place your boat in the most efficient running angle.
Reduce the rise of the bow of your boat during H modeole Shot.
Eliminate bow porpoising (bow bounce).
Keep your boat level at all times.

These actions will result in a smoother ride and the best possible fuel efficiency.

The Auto Glide has 3 automatic operating modes, 4 automatic settings and 2 manual operating modes. Although you will probably keep your Auto Glide in automatic mode, you can immediately switch to manual mode by simply pressing one of the 4 up/down buttons on the keypad.

The main components are the Auto Glide key. Pad, the Auto Glide control box, the main control box harness, and various cables. These cables connect the Auto Glide system to your engine(s), GPS unit, network, and/or a standalone GPS antenna/receiver.

The boat must be equipped with the unique Lenco fin system with Lenco Electric. Actuators. It's a MUST in all applications.

For aftermarket systems:

The Lenco Glide system will work on ALL boats with ALL engines. GPS data is used to provide data to the control box. An optional connection to the NMEA 2000 network is included. For OEM system:

For OEM system:

Connection to analog network systems is available.
Connection to CANbus based motors is available. See list below.
Boat must have a NMEA 2000 GPS network or NMEA 2000 antenna receiver.
NMEA 0183 will work, but will have slower signal response. Lenco offers an optional NMEA 2000 GPS antenna receiver and stainless steel mounting bracket.

Kit contains
1 30254 -001D Auto Glide Keypad Control
1 30255-001 Auau Glide Control Box for Single Actuator
1 30248-001 Auto Slip Control Box Harness for Single Actuator
1 30259-001D CAN Bus #1 NMEA2000 Cable - 2.5'

Available for these CANbus based motors:

NMEA2000 engines

Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N: 6Y98A2D00000)
Evinrude
Honda
Suzuki
E
Volvo Penta (non-EVC engines) (with a Volvo NMEA2000 gateway - Volvo P/N 3889757)

J1939 Engines

Volvo Penta (EVC Engines)
Yanmar
Caterpillar
Cummins
Detroit Diesel
John Deere
Steyr

SmartCraft Engines

Mercury - Verado
Mercury - Optimax with SmartCraft ECU
Mercruiser with SmartCraft ECU
Cummins/Mercruiser with SmartCraft ECU
Cummins/Mercruiser with SmartCraft ECU
/li>

This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information,

A variety of seafood can help meet your boating needs. Today, our products are known for their rugged, easy-to-use design and reliability. Really efficient, fully automatic automatic boat/cut tag control system! Since you are leaving the platform and heading home, the automated taxi system will control your "trim" tab! "Auto-roll" uses engine data and GPS data (depending on your installation method) to adjust the Lenco trim as needed to set the rudder to the most efficient steering angle. After installingFor the Auto Glide system, determine the best operating angle during the installation process. Auto Glide has 3 automatic operating modes, 4 automatic settings and 2 manual operating modes. Although you are more likely to keep "auto glide" in automatic mode, you can immediately switch to manual mode simply by pressing one of the 4 up/down buttons on the keypad. The main components include an automatic sliding keypad, an automatic sliding control box, a main control box wiring harness and various cables. These cables connect the Auto Glide system to the engine, connect the GPS to the network GPS unit and/or a separate GPS antenna/receiver. functionality. Automatically set your boat to the most efficient driving angle.
PRODUCT ID: 56422
SKU: NVN-56422
CSKU: CWR-56422
REWRITE: 67533-lenco-auto-glide- boat-leveling -system-f-single
MPN: 15504-101
UPC: 874847007276
ASIN: B00TJ5JKSK
WSKU: LEN15504101
SSKU: LEN-15504-101
KSKU: LEN15504101
GSKU:
MSKU:
LSKU: 622-15504101
NAME: Lenco Auto Glide Boat Leveling System for Single Actuator Tab Systems with Existing NMEA 2000
EX_NAME: LENCO AUTO GLIDE SINGLE ACTUATOR SYSTEM F/NMEA 2000 EXISTING
PTITLE: Existing NMEA 2000 Lenco Auto Glide boat leveling for single actuator tab systems with existing NMEA 2000
TYPE: Boating Equipment | Trim Tabs
SELLER: Lenco Marine
VEHICLES AND PARTS> VEHICLE PARTS AND ACCESSORIES> WATERCRAFT PARTS AND ACCESSORIES

Lenco 15504-101 Auto Replacement Kit Glide for Single Actuator
Lenco Auto Glide Boat Leveling System for Single Actuator Tab Systems with Existing NMEA 2000

Gtags:

Lenco

GSpecs:

Lenco Auto Glide Boat Leveling System with Single Actuator Tab Systems with Existing NMEA 2000 Product Description

Auto Glide Boat Leveling System - Single Actuator Kit without GPS Antenna or Network - For Boats with NMEA Networks 2000 Existing A true automatic boat control/trim Tab control system that actually works - completely and automatically. The Auto Glide system controls your trim tabs from the moment you leave your dock until you return home! Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimal operating angle is determined during the setup process after installing your Auto Glide system. Imagine that the running angle of your boat is measuredd 25 times per second and this data is used by the new Auto Glide control box to: - Automatically put your boat in the most efficient running angle. - Reduce the rise of your boat's bow during holeshot mode. - Eliminate bow porpoising (bow bounce). - Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency. Note: Auto Glide does not control the "trim" function of your engine(s). Remember to use the trim function exactly as you would in the normal operation of your boat. The Auto Glide control box (brain) consists of gyroscopes, accelerometers and very sophisticated new patented software. The Auto Glide has 3 automatic operating modes, 4 automatic settings and 2 manual operating modes. Even if you keepprobably your Auto Glide in automatic mode, you can immediately switch to manual mode by simply pressing one of the 4 up/down buttons on the keypad. All of these functions are fully explained in our Owner's Manual B/Operating Instructions.

Attributes Lenco 15504101

Compatibility: Single Actuator Compensator tabs and Boats without existing NMEA 2000 networks
Type: Keypad

Lenco 15504101 Features and benefits

Automatic pitch and roll corrections
Automatically adjusts the boat to the most fuel-efficient position.
Manual control at the touch of a button .
Built-in automatic trim tab retraction
Totally waterproof keypad and control box
Three custom settings
Limited warranty 2 years

Lenco 15504101Installation Instructions

Auto Glide Quick Reference Guide_TCHDAT.pdf
15504-101_TCHDAT.pdf

Auto Boat Leveling System Glide for Single Actuator Tab Systems with Existing NMEA 2000

A true automatic boat control/trim tab control system that actually works - completely and automatically!

The Auto Glide system controls your trim tabs from the time you leave your dock until you return home!

Auto Glide uses engine data and GPSa data (depending on your method of d 'installation) to drive your boat at the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimal running angle is determined during the setup process after installing your Auto Glide system.

Imagine your boat's running angle is measured 25 times per secondof and that this data is used by the new Auto Glide control. box for:

Automatically place your boat in the most efficient running angle.
Reduce the amount of bow lift on your boat during hole shooting mode.
Eliminate bow porpoising (bow bounce).
Keep your boat level at all times.

These actions will result in a smoother ride and the best fuel efficiency possible.

The Auto Glide has 3 automatic operating modes, 4 automatic settings and 2 modes manual operation. Although you will likely keep your Auto Glide in automatic mode, you can immediately switch to manual mode with just the press of a button of the 4 up/down buttons on the keypad.

The main components are the Auto Glide keypad, the Auto Glide control box, the main control box harnessof and various cables. These cables connect the Auto Glide system to your engine(s), GPS unit, network, and/or a standalone GPS antenna/receiver.

The boat must be equipped with the Auto Glide system. Lenco single fin with Lenco Electric. Actuators. It is a MUST in all applications.

For aftermarket systems:

The Lenco Glide system will work on ALL boats with ALL engines. GPS data is used to provide data to the control box. An optional connection to the NMEA 2000 network is included. For OEM system:

For OEM system:

Connection to analog network systems is available.
Connection to CANbus based motors is available. See list below.
Boat must have a NMEA 2000 GPS network or NMEA 2000 antenna receiver.
NMEA 0183 will work, but will have slower signal responseyou. Lenco offers an optional NMEA 2000 GPS antenna receiver and stainless steel mounting bracket.

Kit contains
1 30254- 001D Auto-Slide Keypad Control
1 30255-001 Single Actuator Auto-Slide Control Box
1 30248-001 Single Actuator Auto-Slide Control Box Harness
1 30259-001D CAN Bus n° 1 NMEA2000 cable - 2.5'

Available for these CANbus based motors:

NMEA2000 motors

Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway Ref: 6Y98A2D00000)
Evinrude
Honda
Suzuki
E
Volvo Penta (non-EVC engines) (with Volvo NMEA2000 gateway - Volvo P/N 3889757)

J1939 engines

Volvo Penta (EVC engines)
Yanmar
Caterpillar
Cummins
Detroit Diesel
John Deere
Steyr

SmartCraft Engines

Mercure - Verado
Mercury - Optimax with SmartCraft ECU
Mercruiseravec SmartCraft ECU
Cummins/Mercruiser with SmartCraft ECU

This product can expose you to chemicals, including di(2-ethylhexyl phthalate (dehp), known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information,

A variety of seafood can help you meet your boating needs Today, our products are known for their sturdy, easy-to-use design and reliable system. truly efficient automatic boat control/cut tags, fully automatic Since you are leaving the dock and heading home, the automated taxi system will control your "trim" tab!auto taxi" uses engine data and GPS data (depending on your installation method) to adjust Lenco trim as needed to set the rudder to the most efficient steering angle. After installing the Auto Glide system, determine the best operating angle during the installation process. Auto Glide has 3 automatic operating modes, 4 automatic settings and 2 manual operating modes. Although you will probably keep "auto glide" in automatic mode, you can immediately switch to manual mode by pressing one of the 4 up/down buttons on the keypad. The main components include an automatic sliding keypad, an automatic sliding control box, a main control box wiring harness and various cables. These cables connect the Auto Glide system to the engine, connect the GPS to the network GPS unit and/or a separate GPS antenna/receiver. workedlity. Automatically put your boat at the most efficient driving angle.

Lenco Auto Glide Boat Leveling System for Single Actuator Tab Systems with Existing NMEA 2000 Associated ProductsLenco Auto Glide Adapter Cable for SmartCraft/Mercury - 2.5'
Lenco Auto Adapter Cable Glide for/ Command Link / Yamaha - 2.5'
Lenco Auto Glide f/J1939 adapter cable - 2.5'
Lenco Auto Glide CANbus#1 NMEA2000 adapter cable - 2.5'
Lenco Auto Glide CANbus #2 GP/NMEA 2000 adapter cable - 2.5'
Extension cable for Lenco Auto Glide adapter - 10'
Extension cable for Lenco Auto Glide adapter - 20 '
Extension cable for Lenco Auto Glide adapter - 30'
Extension cable for Lenco Auto Glide adapter - 40'
Extension cable for Lenco Auto Glide adapter - 50'
br />

Frequently asked questions (FAQ) about the Lenco Auto Glide f/Singl boat leveling systeme Actuator Tab Systems with Existing NMEA 2000 Who is Lenco Marine?
How to Describe the Lenco Auto Glide Boat Leveling System for Single Actuator Tab Systems with Existing NMEA 2000?
What is the type of product?
What is the weight of the product?
What is the compatibility of this product?
Who is Lenco Marine? Trim tabs make the most important difference in how your boat will sail and operate. Lenco compensators will make your boating experience smoother, drier, faster and with increased safety, whether on a high-performance family cruiser or a small skiff. Lenco's balls rew design is more reliable, twice as powerful and offers instant response which makes them very user friendly. How to describe the Lenco Auto Glide Boat Leveling System with Single Actuator Tab Systems with Existing NMEA 2000? A varietyseafood can help you meet your boating needs. Today, our products are known for their rugged, easy-to-use design and reliability. Really efficient, fully automatic automatic boat/cut tag control system! Since you are leaving the platform and heading home, the automated taxi system will control your "trim" tab! "Auto-roll" uses engine data and GPS data (depending on your installation method) to adjust the Lenco trim as needed to set the rudder to the most efficient steering angle. After installing the Auto Glide system, determine the best operating angle during the installation process. Auto Glide has 3 automatic operating modes, 4 automatic settings and 2 manual operating modes. Although it is more likely that you keep "auto glide" in automatic modeode, you can immediately switch to manual mode by pressing one of the 4 up/down buttons on the keyboard. The main components include an automatic sliding keypad, an automatic sliding control box, a main control box wiring harness and various cables. These cables connect the Auto Glide system to the engine, connect the GPS to the network GPS unit and/or a separate GPS antenna/receiver. functionality. Automatically position your boat at the most efficient driving angle.

The Auto Boat Leveling System for Single Actuator Tab Systems with Existing NMEA 2000 is the only auto tab system that actually works
Fully automatic and requiring no human intervention, the Auto Glide system controls your trim tabs from the helm
The Auto Glide boat leveling system for single actuator tab systems with NMEA 2000 Existing is a true automatic boat control and trim tab control system

Automatic boat leveling system for single actuator tab systems with existing NMEA 2000 A True boat leveling system automatic boat control/trim tab control system that actually works - completely and automatically!
The Auto Glide system controls your trim tabs from the helm station or any other location on the boat.
No more manual adjustments, no more hassle, no more worries.

What is the type of product? Keypad

Automatic Boat Leveling System for Single Actuator Tab Systems with Existing NMEA 2000 is the Only Auto Tab System That Actually Works
Fully automatic and requires no intervention human, the Auto Glide system controls your trim tabs from the helm
TheAuto Glide boat leveling system for single actuator flap systems with existing NMEA 2000 is a true automatic boat and trim tab control system
Auto Glide boat leveling system for tab systems single actuator with existing NMEA 2000 A true automatic boat control/trim tab system that actually works - completely and automatically!
The Auto Glide system controls your trim tabs from the helm station or all other location on the boat.
No more manual adjustments, no more hassle, no more worry.
The Auto Glide Kit is a fully automatic boat leveling system that uses GPS and an on-board network to create a smooth and relaxing navigation experience.
The Auto Glide kit is easy to install, with no drilling or wiring required. and can be removed at any time.
This kit includesthe following: - A single actuator trim tab system - A Lenco Auto Glide kit without GPS antenna or network
Tired of manually adjusting your boat's trim to keep it level?
Auto Glide is an automatic boat leveling system that uses a single actuator to control the operation of the trim tab.
It does this using NMEA 2000 networked GPS sensors, included in the kit .

What is the weight of the product? 4How compatible is this product? Single-actuator trim tabs and boats without existing NMEA 2000 networks

Save $836 when you purchase the Lenco Auto Glide Boat Leveling System for Tab Systems single actuator with existing NMEA 2000 systemsfor only $1,022 from NVN Marine! Same day dispatch before 3 p.m. Lenco Auto Glide Boat Leveling System with Tab SystemsSingle Actuator es with Existing NMEA 2000 Technical Specifications

Type:	Boat Equipment \| Compensating Tabs
Seller:	Lenco Marine
Weight:	3.5 lbs

Lenco Auto Glide Boat Leveling System with Tab Systems Single Actuator with Existing NMEA 2000 User ReviewsLenco Auto Glide Boat Leveling System with Single Actuator Tab Systems with Existing NMEA 2000 Shipping & Returns

ShippingWeight:	3.5 lbs
Box sizes:	7.00 (h) x 7, 00 (l) x 15.00 (l)
Cubic feet:	735.0
Recordable:	Yes
P65:	Yes

For detailed shipping terms, pleasePlease review our shipping policy and you can find our return and refund policy here.