NavPod RailMount Pre-Cut f/Simrad NSS7 evo3 & B&G Zeus3 7 Boat Outfitting

RailMount Pre-Cut for Simrad NSS7 evo3 & B&G Zeus3 7

RailMount NavPods are best used to mount an autopilot control, navigation instrument or a small chartplotter on an existing base protector. Fits any 1", 1.125" or 1.25" diameter tube. A stainless steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing when you are sitting under the vehicle on a rainy day All wiring runs from the NavPod, down the center of the stainless steel arm (the available space is 0.75″ inside the narrowest part of the arm, so keep this in mind when planning your cable route; most transducer cables will not pass through the arm), and in the pedestal protection This application provides a clean and sturdy installation for the. electronic, without having to replace the protectionction of the base.

The rail mounts are designed for all common standard-sized instruments, as well as 7 and 9 inch chart plotters.

Structural rigidity – The Gen3 improvements now include a thicker gauge acrylic-coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.

Waterproof Seal – All RailMount NavPods are manufactured with a double seal system providing an excellent seal. This seal provides the best protection for your marine electronics. NavPods are designed to withstand conmost difficult and wet offshore navigation editions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The internal Poron Microcell polyurethane gasket is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel – We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. Tamper-resistant, nickel-chrome-plated stainless steel screws provide security combined with a little style!

Commitment to quality – We stand by our commitmentment by offering a 10-year warranty on all new NavPods Gen3.

PRODUCT ID: 92200
SKU: NVN-92200
CSKU: CWR-92200
REWRITE: 103311-navpod-railmount-pre-cut-f-simrad-nss7-evo3
MPN: RMX4500-09
UPC:
ASIN:
WSKU: NAVRMX450009
SSKU:
KSKU:
GSKU:
MSKU:
LSKU: NAME: Pre-cut NavPod RailMount for Simrad NSS7 evo3 and B&G Zeus3 7
NAME_EX: Pre-cut NAVPOD RAIL Mount for B&G ZUES3 7/SIMRAD NSS7 EVO3
br>PTITLE: Pre-cut NavPod RailMount f/Simrad NSS7 evo3 and B&G Zeus3 7
TYPE: Boat Equipment | Display Mounts
SELLER: NavPod
ELECTRONICS> MARINE ELECTRONICS

NavPod RMX4500-09 RailMount for Simrad NSS7 evo3

Gtags:

Fish finder

GSpecs:

Pre-cut NavPod RailMount for Simrad NSS7 evo3 and B&G Zeus3 7 Product description

Pre-cut RailMount for Simrad NSS7 evo3 and B&G Zeus3 7

RailMount NavPods are ideal for mounting an autopilot control, navigation instrument or small chartplotter on an existing protective base. Fits any 1", 1.125" or 1.25" diameter tube. A stainless steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing when you are sitting under the vehicle on a rainy day All wiring runs from the NavPod, down the center of the stainless steel arm (the available space is 0.75″ inside the narrowest part of the arm, so keep this in mind when planning your cable route; most transducer cables will not pass through the arm), and in the cradle protection This application provides an i.Clean, sturdy installation for electronics, without having to replace the base guard.

The rail mounts are also designed for all popular standard-sized instruments like 7 and 9 inch chartplotters .

Structural Rigidity – Gen3 enhancements now include thicker gauge acrylic coated ABS material which improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.

Waterproof Seal – All RailMount NavPods are manufactured with a double seal system providing an excellent seal. This seal offers the best protectionwe for your marine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The internal Poron Microcell polyurethane seal is now 50% thicker and is not subject to "compression adjustment" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel – We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. Tamper-proof nickel-chrome-plated stainless steel screws provide combined securityborn to a little style!

Commitment to quality – We stand behind our commitment by offering a 10-year warranty on all new NavPods Gen3.

Frequently Asked Questions (FAQ) about the NavPod RailMount Pre-Cut f/Simrad NSS7 evo3 & B&G Zeus3 7 Who is the NavPod?
How to describe the NavPod RailMount Pre-Cut f/Simrad NSS7 evo3 & B&G Zeus3 7?
Who is the NavPod? Navpod is a gambleA better way to mount your fishfinder, radar or GPS. The unique watertight seal, build quality and attractive design make the best-built instrument housing ever available to the marine industry. Features of all Navpods include waterproof silicone seal, tamper-proof clips for added security and convenience, concealed wiring and clean installation for easy access. How to describe the NavPod RailMount Pre-Cut f/Simrad NSS7 evo3 & B&G Zeus3 7? "

NAVPOD RMX4500-09 Railmount

MBmodel: RMX4500-09

Pre-cut RailMount for Simrad NSS7 evo3 / B&G Zeus3 7

The NavPod RailMount are best used for mounting an autopilot control, navigation instrument or small chart plotter to an existing base guard. Fits any 1" or 1.25" diameter. A nickel-chrome plated stainless steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle in rainy weather. All wiring runs from the NavPod, through the center of the stainless steel arm and into the base shield. This application provides a clean, sturdy installation for electronics without replacing the base guard.

Rail mounts are designed for all popular standard size instruments as well as chart plotters. 7 and 9 inches.

Structural rigidity — Lhe Gen3 improvements now include thicker acrylic-coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.

Watertight seal — All NavPod RailMounts are manufactured with a double seal system providing excellent sealing. This seal provides the best protection for your marine electronics. The NavPod are designed to withstand the harshest wet offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The internal seal in poPoron Microcell lyurethane is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The gasket will continue to do its job.

Chrome Nickel Plated Stainless Steel — We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional NavPod series. Tamper-proof nickel-chrome-plated stainless steel screws provide security combined with a little style!

Specifications

Overall size of the NavPod
Height	7.69
Width	11.86
Depth	5.5
Overall assembly size
Height	10.5
Width	13.91
Depth	6.3
Usable face
Height	6
Width	9.95
Depth	4.125
Maximum cutout
Height	5.5
Width	9.5

"

Save $129 when you purchase the NavPod RailMount Pre-Cut f/Simrad NSS7 evo3 and B&G Zeus3 7 for only $420 from NVN Marine! Same day shipping before 3pm. Simrad NSS7 evo3 & B&G Zeus3 7 Technical specifications

Type:	Boat Equipment \| Display Media
Supplier:	NavPod

NavPod RailMount Pre-Cut f/Simrad NSS7 evo3 and B&G Zeus3 7 User ReviewsNavPod RailMount Pre-Cut f/Simrad NSS7 evo3 and B&G Zeus3 7 Shipping and Return

For detailed shipping policy, please review our Shipping Policy and you can find our Return and Refund Policy here.