Shaft seal PSS 1-¼" shaft 2" tube Marine Hardware
PSS Shaft Seal 1-1/4" Shaft 2" TubeShaft Diameter: 1-1/4"
Stern tube Diameter (D): 2"
Total length (A): 7.38"
Total length (compressed) ( Compressed A): 6.38"
Rotor Diameter (B): 2.875"
Carbon Collar Diameter (C): 2.5"
Rear Collar Length (E): 1.5"
PSS Shaft Seal is the marine mechanical seal best-selling worldwide and is installed as standard equipment by many of the world's leading boat builders/yards. The PSS shaft seal is also recognized as the leading retrofit (aftermarket) seal in the global market. Certified by Bureau Veritas, ABS and Rina: Boat builders/yards recognize the benefits and value of installing PSS as it eliminates the constant maintenance and cost associated with traditional cable glands. PSS ai shaft sealto eliminate water in the bilge (100% waterproof) and wear on the propeller shaft.al can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6 " (150 mm).
PSS shaft seal is a mechanical seal that is created between the flat surfaces of the rotating stainless steel rotor and the fixed carbon flange. The carbon fixed bridle is attached to the ship's stern tube with hose clamps and the carbon bridle is attached to the front of the bellows with hose clamps. The stainless steel rotor is mounted on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is attached to the shaft with set screws. This compression (preload) maintains contact between the faces and allows the PSS to compensate for propeller thrust. The carbon flange is bored larger than the diameter of the shaft, allowing it to "float" around the shaft et thus compensates for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two O-rings which are recessed into the collar bore. These O-rings rotate with the stainless steel shaft and rotor and experience no wear during operation.
**As with any rubber hose below the waterline, PSS bellows must be inspected regularly for signs of wear, aging or chemical deterioration. PYI suggests, as preventative maintenance, that the PSS bellows be replaced every six years. When replacing the bellows, it is recommended to also replace the stainless steel rotor O-rings and adjustment screws. acid fumes will accelerate rubber deterioration, as will an ozonator.
Maintenance kit includes the items you need to properly maintain your rear sealbre PSS. Kit includes one (1) PSS and two (2) bellows. O-rings, five (5) set screws, four (4) new hose clamps and an Allen key.
PSS Type A Shaft Seal is a mechanical end face seal. The sealing surface is formed between the plane of the stainless steel rotating rotor and the fixed carbon fiber bearing.
PRODUCT ID: 50844
SKU: NVN-50844
CSKU: CWR-50844
REWRITE: 61955-pss-shaft-joint-1-shaft-2-tubes
MPN: 02- 114-200
UPC: 839662007153
ASIN: B001HBRAV8
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: PSS Shaft Seal 1-¼" Shaft 2" Tube
EX_NAME: PSS SHAFT SEAL 1 1/4" SHAFT 2" TUBE
PTITRE: PSS Shaft Seal 1-¼" Shaft 2" Tube
TYPE : Marine Hardware | Shaft Seals
SUPPLIER: PSS Shaft Seal
SPORTING GOODS> OUTDOOR RECREATION> BOATING & WATER SPORTSTitleGoogle: PSS (Packless Sealing System) Shaft Seal - 1-1/4" Shaft
Gtags:
GSpecs:
PSS Shaft Seal 1-¼" Shaft 2" Tube Product Description PSS Shaft Seal 1-1/4" Shaft 2" Tube
L Diameter Shaft: 1 -1/4"
Stern tube diameter (D): 2"
Overall length (A): 7.38"
Total length (compressed) (Compressed A): 6.38"
Rotor diameter (B): 2.875"
Carbon Sleeve Diameter (C): 2.5"
Rear Cuff Length (E): 1.5"
PSS Shaft Sealis the best-selling marine mechanical seal in the world and is installed as standard equipment by many of the world's most reputable boat builders/yards. PSS Shaft Seal is. also recognized as the leading retrofit seal (aftermarket) in the global market Certified by Bureau Veritas, ABS and Rina: Boat builders/yards recognize the benefits and value of installing PSS as it eliminates maintenance. , constant adjustment and costs associated with ptraditional cable glands. In addition to these benefits, the PSS shaft seal helps eliminate water in the bilge (100% waterproof) and wear on the propeller shaft. The PSS shaft seal can be easily retrofitted and is available for shafts ranging from 3/4" (20 mm) to 6" (150 mm).
The PSS shaft seal is a mechanical face. seal that is created between the flat surfaces of the rotating stainless steel rotor and the fixed carbon flange. The carbon fixed bridle is attached to the ship's stern tube with hose clamps and the carbon bridle is attached to the front of the bellows with hose clamps. The stainless steel rotor is mounted on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is attached to the shaft with set screws. This compression (preload) maintains contact between the faces and allows the PSS to compensate for propeller thrust. The coach bridlebone is reamed larger than the diameter of the shaft, allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two O-rings recessed into the collar bore. These O-rings rotate with the stainless steel shaft and rotor and experience no wear during operation.
**As with any rubber hose below the waterline, PSS bellows must be inspected regularly for signs of wear, aging or chemical deterioration. PYI suggests, as preventative maintenance, that the PSS bellows be replaced every six years. When replacing the bellows, it is recommended to also replace the stainless steel rotor O-rings and adjustment screws. acid vapors will accelerate the deterioration of the rubber, as will an ozonator.
The kit of mymaintenance includes the items you need to properly maintain your PSS shaft seal. Kit includes one (1) PSS and two (2) bellows. O-rings, five (5) set screws, four (4) new hose clamps and an allen wrench.
PSS Type A shaft seal is a mechanical seal. The sealing surface is formed between the plane of the stainless steel rotating rotor and the fixed carbon fiber bearing.
PSS Shaft Seal, 1-¼" Shaft, 2" Tube Related ProductsPSS Shaft Seal Service Kit, 1-1/4" Shaft, 2" Tube
Frequently Asked Questions (FAQ) About PSS Shaft Seal 1-¼" Shaft 2" Tube Who is PSS Shaft Seal?
How to describe the seal PSS shaft seal 1-¼" Shaft 2" Tube?
Who is the PSS shaft seal? ? The PSS shaft seal is the best-selling marine mechanical seal in the world and is installed as standard equipment by many shipyards and construction companies.among the most renowned boat builders in the world. The PSS Shaft Seal is also recognized as the leading retrofit (aftermarket) seal in the global market. How to describe PSS Shaft Seal 1-¼" Shaft 2" Tube? The PSS Type A shaft seal is a mechanical face seal. The sealing surface is formed between the plane of the stainless steel rotating rotor and the fixed carbon fiber bearing.
Save $46 when you purchase the PSS Shaft Seal 1-¼" Shaft 2" Tube for only $385 at NVN Marine! Same day dispatch before 3 p.m. PSS Shaft Seal 1-¼" Shaft 2" Tube Videos PSS Shaft Seal 1-¼" Shaft 2" Tube Technical Specifications
| Type: | Marine Equipment | Shaft Seals |
|---|---|
| Supplier: | PSS Shaft Seal |
| Weight: | 3.1 lbs |
| Product brochure: | Download the PDF |
| Product installation: | Download PDF |
| Shipping Weight: | 3.1 lb |
|---|---|
| Box sizes: | 6.00 (h) x 6.00 (w) x 9.00 (l) |
| Cubic feet: | 324.0 |
| Returnable: | Yes |
For detailed shipping terms, please view our shipping policy and you can find our return and refund policy here.
