Victron BatteryProtect BP-65 - 65AMP - 6-35 VDC Electrical

BatteryProtect BP-65 - 65AMP - 6-35 VDC

Features:

The BatteryProtect is disconnects the battery from non-essential loads before it is completely discharged (which will damage the battery) or before it no longer has enough power left to crank the engine.
12/24V Auto Range The BatteryProtect automatically senses the system voltage
Simplified Programming The BatteryProtect can be configured to turn on/off at several different voltages. The seven segment display will indicate which setting has been chosen.
A special setting for Li-ion batteries. In this mode, the BatteryProtect can be controlled by the VE.Bus BMS. Note: The BatteryProtect can also be used as a load switch between a battery charger and a Li-ion battery. See connection diagram in the manual.
Ultra low current consumption Thisis important in the case of Li-ion batteries, especially after a low voltage shutdown. Please see our Li-ion battery datasheet and VE.Bus BMS manual for more information.
Overvoltage protection To avoid damage to sensitive loads due to overvoltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V.
Proof of ignition No relays but MOSFET switches, and therefore no sparking.
Delayed alarm output The alarm output is activated if the battery voltage drops below the predefined disconnection level for more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit resistant open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnection and reconnectionon delayed The load will be disconnected 90 seconds after the alarm is activated. If the battery voltage increases again to the connection threshold during this period (after starting the engine for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage increases beyond the preset reconnection voltage.

Warranty Information

This product can expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to P65Warnings.ca.gov.

Please contact your dealer for returns. repair or support issue related to this product.

BatteryProtect 12/24V- -BatteryProtect disconnects thebattery from non-essential loads before it is completely discharged (which will damage the battery) or before there is sufficient power to start the engine. The battery protector is a one-way device. It can only handle current in one direction, so it can handle both the load's current and the charger's current, but it can't handle two currents at the same time. Additionally, current can only flow from the battery terminal to the charging terminal. If a charge is used, the battery is connected to the battery terminal, and if a charger is used, the charger is connected to the battery terminal.
PRODUCT ID: 82905
SKU: NVN-82905
CSKU: CWR-82905
REWRITE: 94016-victron-batteryprotect-bp-65-65amp-6-35
MPN: BPR000065400
br> br> UPC: 8719076034193
ASIN: B01N6ATT8C
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: Victron BatteryProtect BP- 65 - 65AMP - 6-35 VDC
NAME_EX: VICTRON BATTERYPROTECT 12/24V-65A
PTITRE: Victron BatteryProtect BP-65 - 65AMP - 6-35 VDC
TYPE: Electric | Battery Management
SUPPLIER: Victron Energy
VEHICLES & PARTS> VEHICLE PARTS & ACCESSORIES> WATERCRAFT PARTS & ACCESSORIES
CE
Victron BatteryProtect BP-65 -65AMP - 6-35 VDC [BPR000065400]
Victron Battery Protect 12/24V 65A 100A & 220A - BP-65A
CE
Gtags:

Relays

GSpecs:

Victron BatteryProtect BP-65 - 65AMP - 6-35 VDC Product description

BatteryProtect BP-65 - 65AMP - 6-35 VDC

Features:

The BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has enough power remaining to initiate the engine.
12/24V Auto Range The BatteryProtect automatically senses the system voltage
Simplified Programming The BatteryProtect can be configured to turn on/off at several different voltages. The seven segment display will indicate which setting has been chosen.
A special setting for Li-ion batteries. In this mode, the BatteryProtect can be controlled by the VE.Bus BMS. Note: The BatteryProtect can also be used as a load switch between a battery charger and a Li-ion battery. See connection diagram dans the manual.
Ultra low current consumption This is important in the case of Li-ion batteries, especially after a low voltage shutdown. Please see our Li-ion battery datasheet and VE.Bus BMS manual for more information.
Overvoltage protection To avoid damage to sensitive loads due to overvoltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V.
Proof of ignition No relays but MOSFET switches, and therefore no sparking.
Delayed alarm output The alarm output is activated if the battery voltage drops below the predefined disconnection level for more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit resistant open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is generally used to activate a buzzer, an LED or a relay. Delayed load disconnection and delayed reconnection The load will be disconnected 90 seconds after the alarm is activated. If the battery voltage increases again to the connection threshold during this period (after starting the motors for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage increases beyond the preset reconnection voltage.

Warranty Information

WARNING:This product can expose you to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information,

Please contact your dealer for any returns, repairs, or support issues related to this product.

BatteryProtect 12/24V- -BatteryProtect disconnects the batteryDischarge non-essential loads before it is completely discharged (which will damage the battery) or before there is sufficient power to start the engine. The battery protector is a one-way device. It can only handle current in one direction, so it can handle both the load's current and the charger's current, but it can't handle two currents at the same time. Additionally, curreLent can only flow from the battery terminal to the charging terminal. If a charge is used, the battery is connected to the battery terminal, and if a charger is used, the charger is connected to the battery terminal.

Victron BatteryProtect BP-65 - 65AMP - 6-35 VDC Related productsAncor black battery cable 4 AWG - 25'
Ancor red battery cable 4 AWG - 25'
Ancor Yellow 4 AWG Battery Cable - 25'
Ancor Black Battery Cable 2 AWG - 25'
Ancor Red Battery Cable 2 AWG - 25'
Ancor Yellow 2 AWG Battery Cable - 25'
Ancor Heavy Duty Lugs - 2 Gauge Wire - 5/16" Post - 2 Pack
Ancor Heavy Duty Lugs - 2 Gauge Wire 2 - 5/16" Post - Pack of 25
Ancor Heavy Duty Lugs - 1 Gauge Wire - 5/16" Post - 2 Pack
Ancor Heavy Duty Lugs - 1 Gauge Wire - 5/16 Post " - Pack of 25

Frequently Asked Questions (FAQ) About Victron BatteryProtect BP-65 - 65AMP - 6-35 VDC Who is Victron Energy?
How to describe Victron BatteryProtect BP-65 - 65AMP - 6-35 VDC?
Who is Victron Energy? Victron Energy is a global company renowned for its technical innovation, reliability and build quality. Victron products, which excel at efficiently combining two or more distinct energy sources, are recognized internationally as the professional choice for resilient energy storage systems. Victron products include invertersinverters, sine wave inverters/chargers, battery chargers, DC/DC converters, transfer switches, battery monitors and more. How to describe Victron BatteryProtect BP-65 - 65AMP - 6-35 VDC? BatteryProtect 12/24V - BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which will damage the battery) or before there is sufficient power to start the engine. The battery protector is a one-way device. It can only handle current in one direction, so it can handle both load current and charger current, but it cannot handle two currents at the same time. Additionally, current can only flow from the battery terminal to the charging terminal. If a charge is used, the battery is connected to the battery terminal, and if a charger is used, the charger is connected to the battery terminal.erie.

Save $6 when you purchase the Victron BatteryProtect BP-65 - 65AMP - 6-35 VDC for only $36 from NVN Marine! Same day dispatch before 3 p.m. Victron BatteryProtect BP-65 - 65AMP - 6-35 VDC Videos Victron BatteryProtect BP-65 - 65AMP - 6-35 VDC Technical specifications

Type:	Electric \| Battery management
Supplier:	Victron Energy
Weight:	0.5 lbs
User Guide:	Download PDF

Victron BatteryProtect BP-65 - 65AMP - 6-35 VDC User reviewsVictron BatteryProtect BP-65 - 65AMP - 6 -35 VDC Shipping & Returns

Shipping Weight:	0.5 lbs
Box sizes:	3.00 (h) x 3.00 (w) x 5.00 (w)
Cubic feet:	45.0
USPS First Class:	Yes
P65:	Yes