NavPod RMX4102 Pre-cut RailMount f/1 Simrad IS42/B&G Triton2/AP44 square hole instrument Boat Outfitting

RMX4102 Pre-Cut RailMount for 1 Simrad IS42/B&G Triton2/AP44 Square Hole Instrument

RailMount NavPods are best used for mounting an autopilot control, instrument navigation or a small chartplotter on an existing base protection. Fits any 1" or 1.25" diameter tube. A chrome nickel plated stainless steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle on a rainy day. All wiring runs from the NavPod down the center of the stainless steel arm and into the base shield. This application provides a clean, sturdy installation for electronics, without replacing the base guard.

Rail mounts are designed for all popular standard size instruments as well as 7 and 9 plotters inches.

Structural rigidity
Improved themGen3 versions now include thicker gauge acrylic-coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger watertight seal. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially harmful effects on plastic. These new NavPods are really strong!

Waterproof seal
All NavPods are made with a double seal system providing an excellent seal between the front and back of the NavPod . This seal offers the best protection for your marine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen3 improvements include a thicker silicone outer seal aith an improved flush fit. The Poran Microcell Polyurathane internal seal is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The joint will continue to do its job.

Chrome Nickel Plated Stainless Steel
We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. For the NavPod Gen3 we provide tamper proof nickel plated chrome stainless steel screws for added security combined with a little bling!

Commitment to quality
We are committed to produce high quality waterproof enclosures for marine electronics. Wes honor our commitment by offering a 10-year warranty on all new NavPod Gen3s. We want you to be a NavPod customer for life and are ready to earn your trust and loyalty.

Rail mounted navigation modules are most suitable for installing autopilots, navigation instruments or small chartplotters onto existing base guards. Fits any 1" or 1.25"...
PRODUCT ID: 63984
SKU: NVN-63984
CSKU: CWR-63984
REWRITE: 75095-navpod-rmx4102- railmount-pre-cut-f-1-simrad-is42-b-g
MPN: RMX4102
UPC: 659988113471
ASIN: B07XVDMDK1
br> WSKU: NAVRMX4102
SSKU:
KSKU :
GSKU:
MSKU:
LSKU:
NAME: NavPod RMX4102 RailMount Pre-Cut f/1 Simrad IS42/B&G Triton2/ AP44 Square Hole Instrument
EX_NAME: NAVPOD RAILMUNT PRE- CUT FOR A SIMRAD IS42/B&G TRITON2/
PTITLE: NavPod RMX4102 RailMount Pre-cut f/1 Simrad IS42/B&G Triton2/AP44 Square hole instrument
TYPE: Boat outfitter | Display Mounts
SELLER: NavPod
ELECTRONICS> MARINE ELECTRONICS
GPS or Navigation System
NavPod RMX4102 Pre-cut RailMount for a Simrad IS42 / B&G Triton2/AP44 Square Hole Instrument
NavPod RMX4102 RailMount Pre-Cut f/1 Simrad IS42/B&G Triton2/AP44 SquareHole Instrument
GPS or Navigation System
Gtags:

GSpecs:

NavPod RMX4102 Pre-cut RailMount f/1 Simrad IS42/B&G Triton2/AP44 square hole instrument Product Description RMX4102 Pre-cut RailMount for 1 Simrad IS42/B&G Triton2/AP44 square hole instrument

RailMount NavPods are best used for mounting an autopilot controller, navigation instrument, or small chart plotter to an existing protective cradle. Fits any 1" or 1.25" diameter tube. A chrome nickel plated stainless steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle on a rainy day. All wiring runs from the NavPod down the center of the stainless steel arm and into the base shield. This application provides a clean, sturdy installation for electronics, without replacing the base guard.

Rail mounts are designed for all st sized instrumentsandard as well as for 7 and 9 inch plotters.

Structural Rigidity
Gen3 improvements now include a thicker gauge acrylic cap.d ABS material that improves resistance and offers better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially harmful effects on plastic. These new NavPods are really strong!

Waterproof seal
All NavPods are made with a double seal system providing an excellent seal between the front and back of the NavPod . This seal offers the best protection for your marine electronics. NavPods are designed to withstand sailing conditionsion offshore the most difficult and wet. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The Poran Microcell Polyurathane internal seal is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future in order to repair your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel
We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. For the NavPod Gen3 we provide tamper proof nickel plated chrome stainless steel screws for added security combined with a little bling!

Commitment to qualityté
We are committed to producing high quality waterproof enclosures for Marine Electronics. We stand behind our commitment by offering a 10-year warranty on all new NavPod Gen3s. We want you to be a NavPod customer for life and are ready to earn your trust and loyalty.

Rail mounted navigation modules are most suitable for installing autopilots, navigation instruments or small chartplotters onto existing base guards. Fits any 1" or 1.25"...

Frequently Asked Questions (FAQ) about the NavPod RMX4102 RailMount Pre-Cut f /1 Simrad IS42/B&G Triton2/ AP44 Square Hole Instrument Who is the NavPod?
How to describe the NavPod RMX4102 RailMount Pre-Cut f/1 Square Hole Instrument?
Is it cut or not?
How to mount or what is the mounting style of NavPod RMX4102 RailMo Square Hole Instrumentunt Pre-Cut f/1 Simrad IS42/B&G Triton2/AP44?
Who is the NavPod? Navpod is a better way to mount your fishfinder, radar or GPS. The unique watertight seal, build quality and attractive design make the best-built instrument housing ever available to the marine industry. Features of all Navpods include waterproof silicone seal, tamper-proof clips for added security and convenience, concealed wiring and clean installation for easy access. How to describe the NavPod RMX4102 RailMount Pre-Cut f/1 Simrad Square Hole Instrument IS42/B&G Triton2/AP44? Rail mounted navigation modules are most suitable for installing autopilots, navigation instruments or small chartplotters onto existing base guards. Fits any 1" or 1.25"...Is it cut or uncut? CutHow to mount or what is the mounting style of c-hole instrumentarre NavPod RMX4102 RailMount Pre-Cut f/1 Simrad IS42/B&G Triton2/AP44? Rail

Save $118 on the purchase of the NavPod RMX4102 RailMount Pre-Cut f/1 Square Hole Instrument Simrad IS42/B&G Triton2/AP44 for only $381 from NVN Marine! Same day dispatch before 3 p.m. NavPod RMX4102 RailMount Pre-Cut f/1 Simrad IS42/B&G Triton2/AP44 Square Hole Instrument Technical Specifications

Type:	Boat Equipment \| Display Media
Supplier:	NavPod
Weight:	4.4 lbs
Cut/Uncut:	Coupe
Mount Style:	Rail

NavPod RMX4102 RailMount Pre-Cut f/1 Simrad IS42/B&G Triton2/AP44 Square Hole Instrument User ReviewsNavPod RMX4102 RailMount Pre-Cut f/1 Simrad IS42/B&G Triton2/AP44 Square Hole Instrument Expedition and back

Shipping weight:	4.4 lbs
Box sizes:	6.00 (h) x 9.00 (w) x 12.00 (w)
Cubic feet:	648.0
Returnable:	Yes