NavPod RailMount Pre-Cut for Raymarine Axiom 7 & Axiom+ 7 Boat Outfitting

Pre-cut RailMount for Raymarine Axiom 7 and Axiom+ 7

Pre-cut RailMount for Raymarine Axiom 7 and Axiom+ 7 only NO SONAR - NOT FOR AXIOM 7 DV or AXIOM 7 RV ( requires right angle cable part #R70561) (precut is for surface mounting) (fits 1" or 1.25" tubing)

RailMount NavPods are best used to mount an autopilot control, a navigation instrument, or a small chartplotter on an existing plinth. Fits any 1", 1.125" or 1.25" diameter tube. A stainless steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing when you are sitting under the vehicle on a rainy day All wiring runs from the NavPod, down the center of the stainless steel arm (the available space is 0.75″ inside the narrowest part of the arm, so keep that in mind whenplanning your cable route; Most transducer cables will not pass through the arm, and into the base shield. This application provides a clean, sturdy installation for electronics, without replacing the base guard.

RailMounts are designed for all popular standard-size instruments, as well as 7-inch chartplotters. and 9 inches.

Structural Rigidity – Gen3 enhancements now include thicker gauge acrylic-coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects onplastic.

Waterproof Seal – All RailMount NavPods are made with a double seal system providing an excellent seal. This seal provides the best protection for your marine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with a flush fit. The internal Poron Microcell polyurethane gasket is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel – We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod key for better holding capacitywhen tightening than the screws used on our traditional series NavPod. Tamper-proof nickel-chrome-plated stainless steel screws provide security combined with a little style!

Commitment to quality – We stand behind our commitment by offering a 10-year warranty on all new NavPods Gen3.

PRODUCT ID: 75050
SKU: NVN-75050
CSKU: CWR-75050
REWRITE: 86161-navpod-railmount-pre-cut-for-raymarine - axiom-7
MPN: RMX4400-11
UPC:
ASIN:
WSKU: NAVRMX440011
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: Pre-cut NavPod RailMount for Raymarine Axiom 7 and Axiom+ 7
NAME_EX: PRE-CUT NAVPOD RAIL MOUNT FOR RAYMARINE AXIOM 7
PTITLE: Pre-cut NavPod RailMount for Raymarine Axiom 7 & Axiom+ 7
TYPE: Boat fittings | Display Stands
SELLER: NavPod
ELECTRONICS> MARINE ELECTRONICS

NavPod - RMX4400 RailMount Uncut

Gtags:

GSpecs:

NavPod Pre-Cut RailMount for Raymarine Axiom 7 & Axiom+ 7 Product Description

Pre-Cut RailMount for Raymarine Axiom 7 & Axiom+ 7

Pre-Cut RailMount for Raymarine Axiom 7 and Axiom+ 7 only NOT OF SONAR — NOT FOR AXIOM 7 DV or AXIOM 7 RV (requires right angle cable part #R70561) (precut is for surface mounting) (fits 1″ or 1.25″ tubes) p>

RailMount NavPods are best used to mount an autopilot controller, navigation instrument, or small chartplotter to an existing protective cradle. Fits any 1", 1.125" or 1.25" diameter tube. A stainless steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing when you are sitting under the vehicle on a rainy day All wiring runs from the NavPod, to the center of the stainless steel arm (the clearance is 0.75″ inside.ior the narrowest part of the arm, so keep that in mind when planning your cable route; Most transducer cables will not pass through the arm, and into the base shield. This application provides a clean, sturdy installation for electronics, without having to replace the base guard.

The rail mounts are designed for all common standard-sized instruments, as well as track plotters. 7- and 9-inch boards.

Structural Rigidity – Gen3 enhancements now include thicker gauge acrylic-coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. Lhe acrylic cap protects ABS from UV and its potentially damaging effects on plastic.

Waterproof Seal – All RailMount NavPods are manufactured with a double seal system providing an excellent seal. This seal provides the best protection for your marine electronics. NavPods are designed to withstand the wettest offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The internal Poron Microcell polyurethane gasket is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel – We use all 316 stainless steel hardware that comes with every NavPod. The large round head tamper-proof screws haveDeeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. Tamper-proof nickel-chrome-plated stainless steel screws provide security combined with a little style!

Commitment to quality – We stand behind our commitment by offering a 10-year warranty on all new NavPods Gen3.

Frequently asked questions (FAQ) about NavPod RailMount Pre-Cut for Raymarine Axiom 7 & Axiom+ 7 Who is the NavPod?
How to describe NavPod RailMount Pre-Cut for Raymarine Axiom 7 & Axiom+ 7?
Who is the NavPod? Navpod is a better way to mount your fishfinder, radar or GPS. The unique watertight seal, build quality and attractive design make the best-built instrument housing ever available to the marine industry. Features of all Navpods include silicone seal andreed, tamper-resistant fasteners for added security and convenience, concealed wiring and clean installation for easy access. How to describe the NavPod RailMount Pre-Cut for Raymarine Axiom 7 and Axiom+ 7? "

NAVPOD RMX4400-11 Railmount

Model: RMX4400-11

Pre-cut RailMount for Garmin GPSMAP 742xs/742/722xs/722

RailMount NavPod are best used for mounting an autopilot control, navigation instrument or small chartplotter to a guard of existing base. Fits any 1" or 1.25. " diametertube. A nickel-chrome plated stainless steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing when seated under the vehicle an rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm and into the base guard. This application provides u.ne clean, sturdy installation for electronics, without replacing the base guard.

Rail mounts are designed for all popular standard size instruments as well as 7 and 9 chart plotters inches.

Structural Rigidity — Gen3 enhancements now include thicker acrylic-coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects ABS from UV rays and its potentially damaging effects on plastic.

Watertight seal — All NavPod RailMounts are manufactured with a double seal system providing excellent waterproofing. This seal offers the best protectionof your marine electronics. The NavPod are designed to withstand the harshest wet offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The internal Poron Microcell polyurethane gasket is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The gasket will continue to do its job.

Chrome Nickel Plated Stainless Steel — We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional NavPod series . Tamper-proof nickel-chrome-plated stainless steel screws provide securityurity combined with a little style!

"

Save $127 when you purchase the NavPod RailMount Pre- Cut for Raymarine Axiom 7 and Axiom+ 7 for only $412 at NVN Marine! Same day shipping before 3pm 7 and Axiom+ 7 Technical specifications.

Type:	Boat fittings \| Display supports
Supplier:	NavPod

NavPod Pre-Cut RailMount for Raymarine Axiom 7 and Axiom+ 7 User ReviewsNavPod Pre-Cut RailMount for Raymarine Axiom 7 and Axiom+ 7 Shipping and Returns

For detailed shipping policy, please see our shipping policy and you can find our return and refund policy here.