Uncut NavPod RMX4900 (usable face = 12.4"L x 7.4"H) (31.5cm W x 18.8cm H) Boat Outfitting

RMX4900 Uncut (Usable Face = 12.4" Width x 7.4" Height) (31.5cm Width x 18.8cm Height)

RailMount NavPods are best used for mounting an autopilot command, navigation instrument or small chartplotter to an existing protective mount. Fits any 1" or 1.25" diameter tube. A chrome nickel plated stainless steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle on a rainy day. All wiring runs from the NavPod down the center of the stainless steel arm and into the base shield. This application provides a clean, sturdy installation for electronics, without replacing the base guard.

The rail mounts are designed for all popular standard size instruments as well as 7 and 7 plotters. 9 inches.

RigidityStructural

Gen3 enhancements now include thicker gauge acrylic-coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger seal. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially harmful effects on plastic. These new NavPods are really strong!

Waterproof seal

All NavPods are made with a double seal system providing an excellent seal between the front and the back of the NavPod. This seal offers the best protection for your marine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. The amGen3 improvements include a thicker silicone outer seal with an improved flush fit. The Poran Microcell Polyurathane internal seal is now 50% thicker and is not subject to "compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices.cs. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel

We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. For NavPods Gen3, we provide tamper-resistant nickel-chrome-plated stainless steel screws for added security combined with a little bling!

Commitment to quality

WeWe are committed to producing high quality waterproof enclosures for marine electronics. We stand behind our commitment by offering a 10-year warranty on all new NavPod Gen3s. We want you to be a NavPod customer for life and are ready to earn your trust and loyalty.

Uncut RMX4900 (usable area = 12.4" W x 7.4" H) (31.5cm L x 18.8cm H) RailMount NavPods are best suited for installing autopilots, navigation tools or small chartplotters on existing systems.Basic protection Hooded. Can be installed on any pipe with a diameter of 1" or 1.25". Nickel-chrome plated stainless steel arms are used to install the NavPod. The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle on a rainy day. All wiring extends from the NavPod to the center of the stainless steel arm.
PRODUCT ID: 63987
SKU: NVN-63987
CSKU: CWR-63987
REWRITE: 75098-navpod-rmx4900-uncut-usable-face-12-4-w
MPN: RMX4900
UPC: 659988110937
ASIN: B0753J6SFJ
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: NavPod RMX4900 Uncut (usable face = 12.4" width x 7.4 " height) (31.5 cm width x 18.8 cm height)
EX_NAME: NAVPOD RAIMount UN-CUT (USABLE FACE = 12.4" width x 7.4" height)
TITLE: NavPod RMX4900 Uncut (usable face = 12.4"L x 7.4"H) (31.5cm W x 18.8cm H)
TYPE: Boat Layout | Display Stands
SELLER: NavPod
ELECTRONICS> MARINE ELECTRONICS NavPod RMX4900 Uncut (Usable Face = 12.5" L x 7.8" H) (38.6 cm W x 24.9 cm H)

Gtags:

Plastic

GSpecs:

Uncut NavPod RMX4900 (usable face = 12.4" width x 7.4" height) (31.5 cm width x 18.8 cm height) Product Description

Uncut RMX4900 ( usable face = 12.4" W x 7.4" H) (31.5 cm W x 18.8 cm H)

RailMount NavPods are best used for mounting an autopilot control, navigation instrument or small chart plotter to an existing protective base. Fits any 1" or 1.25" diameter tube. A chrome nickel plated stainless steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle on a rainy day. All wiring runs from the NavPod down the center of the stainless steel arm and into the base shield. This application provides a clean, sturdy installation for electronics, without replacing the base guard.

Brackets onrail are designed for all popular standard size instruments as well as 7 and 9 inch plotters.

Structural Rigidity

Gen3 enhancements now include a thicker gauge acrylic A cap. BS material which improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially harmful effects on plastic. These new NavPods are really strong!

Waterproof seal

All NavPods are made with a double seal system providing an excellent seal between the front and the back of the NavPod. This seal offers the best protection for your elmarine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The internal Poran Microcell polyurethane seal is now 50% thicker and is not subject to "compression" like many rubber components.sd. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel

We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. For NavPods Gen3, we provide stainless steel tamper-proof screws nChrome plated for added security combined with a little bling!

Commitment to quality

We are committed to producing high quality waterproof cases for l marine electronics. We stand behind our commitment by offering a 10-year warranty on all new NavPod Gen3s. We want you to be a NavPod customer for life and are ready to earn your trust and loyalty.

Uncut RMX4900 (usable area = 12.4" W x 7.4" H) (31.5cm W x 18.8cm H) Rail MountNavPods are most suitable for installing autopilots, navigation tools or small chartplotters onto the existing hooded base guard. Can be installed on any pipe with a diameter of 1" or 1.25". Nickel-chrome plated stainless steel arms are used to install the NavPod. The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle on a busy day.him. All wiring extends from the NavPod to the center of the stainless steel arm.

Frequently Asked Questions (FAQ) about Uncut NavPod RMX4900 (Usable Face = 12.4" Width x 7.4" Height) ( 31.5 cm wide x 18.8 cm high) Who what is the NavPod? How to describe the NavPod RMX4900 uncut (usable face = 12.4" W x 7.4" H ) (12.5" L x 7.4" H)?
Is it cut or uncut?
How to mount or what is the mounting style of the uncut NavPod RMX4900 (usable face = 12 .4" L x 7.4" H) (31.5 cm W x 18.8 cm H)?
How big is the usable surface area of the product?
Who is the NavPod? Navpod is a better way to mount your fishfinder, radar or GPS. The unique watertight seal, build quality and attractive design make the best-built instrument housing ever available to the marine industry. Features of all Navpods include the gasketWaterproof silicone, tamper-resistant fasteners for added security and convenience, concealed wiring and clean installation for easy access. How to describe the NavPod RMX4900 uncut (usable face = 12.4" W x 7.4" H) (31.5 cm W x 18.8 cm H)? Uncut RMX4900 (usable area = 12.4" W x 7.4" H) (31.5 cm W x 18.8 cm H) NavPod RailMount are best suited for installation of autopilots, navigation tools or small chartplotters on the existing base protection. . Can be installed on any pipe with a diameter of 1" or 1.25". Nickel-chrome plated stainless steel arms are used to install the NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the vehicle on a rainy day. All wiring extends from the NavPod to the center of the stainless steel arm. Is it cut or uncut? Uncut How to mount or what is thehe mounting style of the uncut NavPod RMX4900 (usable face = 12.4"L x 7.4"H) (31.5cm W x 18.8cm H)? RailWhat is the size of the usable surface area of the product? 12.4"L x 7.4"H

Save $128 when you purchase the NavPod RMX4900 uncut (usable face = 12.4"L x 7.4"H) (31.5cm W x 18.8cm H)for only $451 at NVN Marine! Same day dispatch before 3 p.m. Uncut NavPod RMX4900 (Usable Face = 12.4" Width x 7.4" Height) (31.5cm Width x 18.8cm Height) Technical Specifications

Type:	Boat fittings \| Display Media
Supplier:	NavPod
Weight:	8.8 lbs
Cut/Uncut:	Uncut
Mounting Style:	Rail
Usable face:	12.4"L x 7.4"H

Uncut NavPod RMX4900 (usable face = 12.4" width x 7.4" height) (31.5 cm width x 18.8 cm height) Shipping and Returns

Shipping Weight:	8.8 lbs
Box Sizes:	6.00 (h) x 8.00 (w) x 11.00 (l)
Cubic feet:	528.0
Returnable:	Yes