NavPod RMX4500-08 Pre-Cut RailMount for Garmin 922 / 922xs / 942 / 942xs Boat Outfitting

RailMount Pre-Cut f/Garmin 922 / 922xs / 942 / 942xs

RailMount NavPods are best used for mounting an autopilot control, navigation instrument or a small chart plotter on an existing protective base. . Fits any 1" or 1.25" diameter tube. A chrome nickel plated stainless steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle on a rainy day. All wiring runs from the NavPod down the center of the stainless steel arm and into the base shield. This application provides a clean, sturdy installation for electronics, without replacing the base guard.

Rail mounts are designed for all popular standard size instruments as well as 7 and 9 plotters inches.

Gen3 – "The best just got better"

Structural Rigidity
Gen3 improvements now include thicker acrylic-coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially harmful effects on plastic. These new NavPods are really strong!

Waterproof seal
All NavPods are made with a double seal system providing an excellent seal between the front and back of the NavPod . This seal offers the best protection for your marine electronics. NavPods are designed to withstand the harshest and wettest offshore sailing conditions. Gen Improvements3 include a thicker silicone outer gasket with an improved flush fit. The Poran Microcell Polyurathane internal seal is now 50% thicker and is not subject to "defined compression" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel
We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. For NavPods Gen3, we provide tamper-resistant, nickel-plated, chrome-plated stainless steel screws for added security combined with a little bling!

Commitment to quality
We are committed toproduce high quality waterproof enclosures for marine electronics. We stand behind our commitment by offering a 10-year warranty on all new NavPod Gen3s. We want you to be a NavPod customer for life and are ready to earn your trust and loyalty.

Rail mounted navigation modules are most suitable for installing autopilots, navigation instruments or small chartplotters onto existing base guards. Fits any 1" or 1.25"...
PRODUCT ID: 66374
SKU: NVN-66374
CSKU: CWR-66374
REWRITE: 77485-navpod-rmx4500-08 -railmount-pre-cut- f-garmin-922
MPN: RMX4500-08
UPC: 659988114379
ASIN: B07TTT3G36
WSKU: NAVRMX450008
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: NavPod RMX4500-08 Pre-Cut RailMount for Garmin 922 / 922xs / 942 / 942xs
NAME_EX: PRE-CUT NAVPOD FOR GARMIN 922/922XS/ 942/942XS
PTITLE: NavPod RMX4500-08Pre-cut RailMount for Garmin 922 / 922xs / 942 / 942xs
TYPE: Boat equipment | Display Mounts
SELLER: NavPod
ELECTRONICS> MARINE ELECTRONICS NavPod RMX4500-08 RailMount Pre-Cut f/Garmin 922 /922xs / 942 / 942xs

Gtags:

GSpecs:

NavPod RMX4500-08 Pre-Cut RailMount for Garmin 922 / 922xs / 942 / 942xs Product Description Pre-Cut RailMount for Garmin 922 / 922xs / 942 / 942xs

RailMount NavPods are Ideal for mounting an autopilot control, navigation instrument or small chartplotter on an existing protective base. Fits any 1" or 1.25" diameter tube. A chrome nickel plated stainless steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing when sitting under the vehicle on a rainy day. All wiring runs from the NavPod down the center of the stainless steel arm and into the base shield. This application provides a clean, sturdy installation for electronics, without replacing the base guard.

Rail mounts are designed for all popular standard size instruments as well as plotters7 and 9 inches.

Gen3 – "The best just got better"

Structural rigidity
Improvements Gen3 now include a thicker gauge acrylic coated ABS material that improves strength and provides better structural rigidity. This thicker material allows for greater sealing. The higher the structural rigidity, the less flex there is when tightening and the more uniform the pressure on the joint. The excellent UV stability of acrylic is combined with the durability of ABS. The acrylic cap protects the ABS from UV and its potentially harmful effects on plastic. These new NavPods are really strong!

Waterproof seal
All NavPods are made with a double seal system providing an excellent seal between the front and back of the NavPod . This seal offers the best protection for your marine electronics. NavPods are designedto withstand the most difficult and wet offshore sailing conditions. Gen3 improvements include a thicker silicone outer gasket with an improved flush fit. The internal Poran Microcell polyurethane seal is now 50% thicker and is no longer subject to "compression".t" like many rubber compounds. This is important when you need to open the NavPod in the future to repair your electronic devices. The seal will continue to do its job.

Chrome Nickel Plated Stainless Steel
We use all 316 stainless steel hardware that comes with every NavPod. Large round head tamper-proof screws have deeper sockets for the NavPod wrench for better holding power when tightening than the screws used on our traditional series NavPod. For NavPods Gen3, we provide tamper-resistant nickel-chrome-plated stainless steel screws for added security combinedwith a little bling!

Commitment to quality
We are committed to producing high quality waterproof enclosures for Marine Electronics. We stand behind our commitment by offering a 10-year warranty on all new NavPod Gen3s. We want you to be a NavPod customer for life and are ready to earn your trust and loyalty.

Rail mounted navigation modules are most suitable for installing pilot auda, navigation instruments or small chartplotters onto existing base guards. Fits any 1" or 1.25"...

Frequently Asked Questions (FAQ) about NavPod RMX4500-08 Pre-Cut RailMount for Garmin 922/922xs/ 942 / 942xs Who is the NavPod?
How to describe the NavPod RMX4500-08 RailMount Pre-Cut f/Garmin 922 / 922xs / 942 / 942xs?
Is it cut or not?
br/> How or what is the mounting style of the NavPod RMX4500-08 RailMount Pre-Cutf/Garmin 922 / 922xs / 942 / 942xs?
Who is the NavPod? Navpod is a better way to mount your fishfinder, radar or GPS. The unique watertight seal, build quality and attractive design make the best-built instrument housing ever available to the marine industry. Features of all Navpods include waterproof silicone seal, tamper-proof clips for added security and convenience, concealed wiring and clean installation for easy access. How to describe the NavPod RMX4500-08 RailMount Pre-Cut f/Garmin922/922xs/942/942xs? Rail mounted navigation modules are most suitable for installing autopilots, navigation instruments or small chartplotters onto existing base guards. Fits any 1" or 1.25"...Is it cut or uncut? Cut

$129

NavPod RMX4500-08 RailMount Pre-Cut f/Garmin 922 / 922xs / 942 / 942xs

$420

Type:	Boat Equipment \| Display Media
Supplier:	NavPod
Weight:	6.2 lbs
Cut/Uncut:	Couped
Mounting Style:	Rail

Shipping Weight:	6.2 lbs
Box Sizes:	7.00 (h) x 10.00 (w) x 14.00 (l)
Cubic feet:	980.0
Returnable:	Yes

For detailed shipping terms, please check our shipping policy and you can find our return and refund policy here.